create_clock - 2020.2 English

Vivado Design Suite Tcl Command Reference Guide (UG835)

Document ID
UG835
Release Date
2020-11-18
Version
2020.2 English

Create a clock object

Syntax

create_clock ‑period <arg> [‑name <arg>] [‑waveform <args>] [‑add] [‑quiet]
    [‑verbose] [<objects>]

Returns

new clock object

Usage

Name Description
-period Clock period: Value > 0
[-name] Clock name
[-waveform] Clock edge specification
[-add] Add to the existing clock in source_objects
[-quiet] Ignore command errors
[-verbose] Suspend message limits during command execution
[<objects>] List of clock source ports, pins or nets

Categories

SDC, XDC

Description

Tip: The XDC > Timing Constraints language templates and the Timing Constraints Wizard in the Vivado IDE offer timing diagrams and additional details around defining specific timing constraints. You can refer to these sources for additional information.

Create a clock object with the specified period or waveform defined in nanoseconds (ns). This command defines primary clocks which are used by the timing engine as the delay propagation starting point of any clock edge. The defined clock can be added to the definition of an existing clock, or overwrite the existing clock.

A virtual clock can be created that has no source in the design. A virtual clock can be used as a time reference for setting input and output delays but does not physically exist in the design.

A clock can also be generated from an existing physical clock, and derive many of its properties from the master clock. Use the create_generated_clock command to derive a clock from an existing physical clock.

Important: If you use create_clock to create a generated clock, instead of create_generated_clock, the created clock does not inherit any of the properties of its source clock. The insertion delay and jitter of the parent clock will not be propagated to the generated clock, causing incorrect timing calculations.

The create_clock command returns the name of the clock object that is created.

Arguments

-period <arg> - (Required) Specifies the clock period of the clock object to be created. The value is specified as nanoseconds (ns) and must be greater than zero (>0).

-name <arg> - (Optional) The name of the clock object to be created. If the name is omitted, a system-generated name will be used based on the specified source <objects>. You can also use the -name option without source <objects> to create a virtual clock for the design that is not associated with a physical source on the design.

-waveform <arg1 arg2 ...> - (Optional) The rising and falling edge times of the waveform of the defined clock, in nanoseconds, over one full clock cycle. You can use multiple rising and falling edges to define the characteristics of the waverform, but there must be an even number of edges, representing both the rising and falling edges of the waveform. The first time specified (arg1) represents the time of the first rising transition, and the second time specified (arg2) is the falling edge. If the value for the falling edge is smaller than the value for the rising edge, it means that the falling edge occurs before the rising edge.
Note: If you do not specify the waveform, the default waveform is assumed to have a rising edge at time 0.0 and a falling edge at one half the specified period (-period/2).

-add - (Optional) Define multiple clocks on the same source for simultaneous analysis with different clock waveforms. Use -name to specify the new clock to add. If you do not specify this option, the create_clock command will overwrite any existing clock of the same name.

-quiet - (Optional) Execute the command quietly, returning no messages from the command. The command also returns TCL_OK regardless of any errors encountered during execution.
Note: Any errors encountered on the command-line, while launching the command, will be returned. Only errors occurring inside the command will be trapped.
-verbose - (Optional) Temporarily override any message limits and return all messages from this command.
Note: Message limits can be defined with the set_msg_config command.
<objects> - (Optional) The ports, pins, or nets which are the source of the specified clock. If you specify a clock on a source object that already has a clock, the new clock will overwrite the original clock unless you also specify the -add option. If no <objects> are specified to attach the clock object to, the clock will be created as a virtual clock in the design.
Note: The first driver pin of a specified net will be used as the source of the clock.

Examples

The following example creates a physical clock called bftClk and defines the clock period:
create_clock -name bftClk -period 5.000 [get_ports bftClk]
Note: If the get_ports command defining the objects is left off of this example, a virtual clock is created in the design rather than a physical clock.
The following example creates a clock named clk on the input port, bftClk, with a period of 10ns, the rising edge at 2.4ns and the falling edge at 7.4ns:
create_clock -name clk -period 10.000 -waveform {2.4 7.4} [get_ports bftClk]
The following example creates a virtual clock since no clock source is specified:
create_clock -name virtual_clock -period 5.000
The following example creates a clock with the falling edge at 2ns and the rising edge at 7ns:
create_clock -name clk -period 10.000 -waveform {7 2} [get_ports bftClk]
Note: Because the falling edge is earlier than the rising edge in the -waveform definition, although it is specified as arg2, it occurs first in the waveform.