write_cfgmem - 2020.2 English

Vivado Design Suite Tcl Command Reference Guide (UG835)

Document ID
UG835
Release Date
2020-11-18
Version
2020.2 English

Create file(s) for programming flash memory.

Syntax

write_cfgmem [‑force] ‑format <arg> ‑size <arg> [‑interface <arg>]
    [‑checksum] [‑disablebitswap] [‑loadbit <arg>] [‑loaddata <arg>]
    [‑quiet] [‑verbose] <file>

Usage

Name Description
[-force] Overwrite existing file
-format Format of the file to generate
-size Size of memory that is being targeted in M Bytes (must be power of 2).
[-interface] Interface used to program device. Default: SMAPx8
[-checksum] Calculate a 32-bit checksum for each file. Memory will be filed with value of 0xFF unless a different byte value is specified. Default: 0xFF
[-disablebitswap] Disable bit swapping in a byte for bitfiles.
[-loadbit] Load bit files into memory from given address.
[-loaddata] Load data into memory from given address.
[-quiet] Ignore command errors
[-verbose] Suspend message limits during command execution
<file> The name of the file to generate

Categories

FileIO

Description

This command formats a design specific configuration bitstream (.bit) file, and any specified data files, into a specified memory configuration file format to program into a flash memory device using the program_hw_cfgmem command. Supported memory configuration file formats are MCS, BIN, and HEX.

Tip: When you generate a cfgmem file with write_cfgmem, by default the bits within a byte are bit-swapped, or mirrored, compared to bytes in the original input bitstream. You can disable bitswap using the -disablebitswap option as described below.

The process whereby the design specific data is loaded or programmed into the Xilinx® FPGA is called configuration. The create_hw_cfgmem command defines a flash memory device used for configuring and booting the hardware device.

After the hw_cfgmem object is created, and associated with the hw_device, the configuration memory can be programmed with the bitstream and other data from a memory configuration file created with the write_cfgmem command. The hw_cfgmem object is programmed using the program_hw_cfgmem command.

The write_cfgmem -loadbit command loads one or more specified bitstream files into the memory configuration file, filling the available memory of the device in an upward or downward direction from a specified starting address. You can also add data files to the memory configuration file, by specifying the starting address to load the file with -loaddata.

Tip: When using -loadbit and -loaddata to fill the memory of the device, you must exercise care to insure that the bitstream and data files fit into the available memory and do not overwrite each other. Any data collisions will cause the write_cfgmem command to fail with an error.

The write_cfgmem command returns a transcript of its process when successful, or returns an error if it fails.

Arguments

-force - (Optional) Overwrite a file of the same name if one exists.

-format [ BIN | HEX | MCS ] - (Required) The format of the memory configuration file to write. Supported values include BIN, HEX, and MCS.

-size <arg> - (Required) Specify the size limit in MBytes of the PROM device that is being targeted. The size must be specified as a power of 2.

-interface <arg> - (Optional) Specify the interface used to program the PROM device. Valid values include SMAPx8 (default), SMAPx16, SMAPx32, SERIALx1, SPIx1, SPIx2, SPIx4, SPIx8, BPIx8, BPIx16. This also determines if byte swapping is enabled or disabled. The default interface is SMAPx8.
Important: The specified interface format of the configuration memory file is critical to properly programming the flash memory device with the program_hw_cfgmem command. You should be careful to use this option to match the generated file with the target cfgmem_part.

-checksum - (Optional) Calculate a 32-bit checksum for the PROM file. The device memory will be filled with the default value of 0xFF unless a different byte value is specified. This option generates a checksum value appearing in the memory configuration file. This value should match the checksum in the device programmer. Use this option to verify that correct data was programmed into the flash memory.

-disablebitswap - (Optional) Disable the default bit swapping for bytes in the bitstream files. By default, in the files written by write_cfgmem, the bits within a byte are bit-swapped, or mirrored, compared to bytes in the original input BIT files. This option disables the bit swapping in the output files.

-loadbit <arg> - (Optional) Specify the starting address of the PROM device to begin loading one or more bitstream files. The option is specified as a string with the form:
"up|down 0x0 <bitfile1>.bit <bitfile2>.bit"
Where:
  • up | down - This option loads one or more BIT files into memory, starting from the specified address, in either and upward or a downward direction.
  • 0x0 - The starting address to load the bitstream, specified as a hexadecimal value.
  • <bitfile>.bit - The bitstream (.bit) file to load into the flash memory device. You can specify multiple bitstream files, causing the files to be concatenated in a daisy chain.
Tip: You can only specify the -loadbit option once, but you can repeat the arguments as needed to load multiple bitstream files from different starting addresses:
-loadbit "up 0 bitfile1.bit up 0xFFFFFF bitfile2.bit" 
-loaddata <arg> - (Optional) Load the specified data files into the memory of the configuration device from the starting address. The -loaddata option is a string in the same form as the -loadbit argument, specifying the direction, starting address, and data file names to add into the memory configuration file. Data files will be added to the flash memory device as is, with no additional formatting.
  • up | down - This option loads one or more DATA files into memory, starting from the specified address, in either and upward or a downward direction.
  • 0x0 - The starting address to load the data file, specified as a hexadecimal value.
  • <data_file> - A data file to load into the flash memory device. You can specify multiple data files, causing the files to be concatenated in a daisy chain.
Note: Although both -loadbit and -loaddata are marked as optional, at least one argument must be used to provide the data for the memory configuration file.
-quiet - (Optional) Execute the command quietly, returning no messages from the command. The command also returns TCL_OK regardless of any errors encountered during execution.
Note: Any errors encountered on the command-line, while launching the command, will be returned. Only errors occurring inside the command will be trapped.
-verbose - (Optional) Temporarily override any message limits and return all messages from this command.
Note: Message limits can be defined with the set_msg_config command.
<file> - (Required) The filename of the memory configuration file to write. The file extension will match the format specified (.mcs), and is not required as part of the file name.
Note: If the path is not specified as part of the file name, the file will be written into the current working directory, or the directory from which the tool was launched.

Example

The following example writes the specified memory configuration file in the MCS format, with a size limit of 64 MB, loading the specified bitstream file moving up from the starting address:
write_cfgmem -format MCS -size 64 -loadbit "up 0x0 \  
C:/Data/Vivado_Debug/project_debug/project_debug.runs/impl_1/sinegen_demo.bit" \  
config_memory1