- Power off the board.
- Connect the JTAG port on the board with the JTAG cable to your workstation.
- Connect the serial port on the board to your workstation.
- If your system has Ethernet, also connect the Ethernet port on the board to your local network.
- Ensure that the mode switches are set to JTAG mode. Refer to the board documentation for details.
- Power on the board.
- Open a console on your workstation and start with preferred serial communication program (For example, kermit, minicom) with the baud rate set to 115200 on that console.
- Run the
petalinux-bootcommand as follows on your workstation:$ petalinux-boot --jtag --prebuilt 3 --hw_server-url <hostname:3121>Note: If you wish not to use prebuilt capability for JTAG boot, refer to Additional Options for Booting with JTAG.The
--jtagoption tellspetalinux-bootto boot on hardware via JTAG, and the--prebuilt 3option boots the Linux kernel. Wait for the appearance of the shell prompt on the command console to indicate completion of the command.Note: To know more about different boot levels for prebuilt option, see Using petalinux-boot Command with Prebuilt Images.The example of the message on the workstation command console for successful
petalinux-bootis:[3.958]PLM Initialization Time [4.021]***********Boot PDI Load: Started*********** [4.099]Loading PDI from JTAG [4.159]Monolithic/Master Device [4.285]0.153 ms: PDI initialization time [4.359]+++Loading Image#: 0x1, Name: lpd, Id: 0x04210002 [4.444]---Loading Partition#: 0x1, Id: 0xC [27.674]**************************************** [31.900]Xilinx Versal Platform Loader and Manager [36.295]Release 2021.1 Jun 1 2021 - 15:25:35 [40.607]Platform Version: v2.0 PMC: v2.0, PS: v2.0 [45.002]BOOTMODE: 0x0, MULTIBOOT: 0x0 [48.299]**************************************** [52.564] 48.010 ms for Partition#: 0x1, Size: 2288 Bytes [57.426]---Loading Partition#: 0x2, Id: 0x0 [61.780] 0.516 ms for Partition#: 0x2, Size: 48 Bytes [65.881]---Loading Partition#: 0x3, Id: 0x0 [106.053] 36.331 ms for Partition#: 0x3, Size: 59280 Bytes [108.364]---Loading Partition#: 0x4, Id: 0x0 [112.297] 0.012 ms for Partition#: 0x4, Size: 2640 Bytes [117.154]---Loading Partition#: 0x5, Id: 0x0 [121.089] 0.014 ms for Partition#: 0x5, Size: 3440 Bytes [125.944]---Loading Partition#: 0x6, Id: 0x0 [129.871] 0.007 ms for Partition#: 0x6, Size: 80 Bytes PSM Firmware version: 2021.1 [Build: Jun 1 2021 15:25:35 ] [139.818]+++Loading Image#: 0x2, Name: pl_cfi, Id: 0x18700000 [145.126]---Loading Partition#: 0x7, Id: 0x3 [985.682] 836.632 ms for Partition#: 0x7, Size: 1304480 Bytes [988.250]---Loading Partition#: 0x8, Id: 0x5 [1604.539] 612.366 ms for Partition#: 0x8, Size: 933344 Bytes [1607.150]+++Loading Image#: 0x3, Name: aie_subsys, Id: 0x0421C005 [1612.862]---Loading Partition#: 0x9, Id: 0x7 [1619.981] 3.108 ms for Partition#: 0x9, Size: 352 Bytes [1622.170]+++Loading Image#: 0x4, Name: fpd, Id: 0x0420C003 [1627.291]---Loading Partition#: 0xA, Id: 0x8 [1631.722] 0.422 ms for Partition#: 0xA, Size: 1040 Bytes [1636.526]+++Loading Image#: 0x5, Name: apu_subsystem, Id: 0x1C000000 [1642.264]---Loading Partition#: 0xB, Id: 0x0 [1660.095] 13.821 ms for Partition#: 0xB, Size: 29520 Bytes [1662.496]---Loading Partition#: 0xC, Id: 0x0 [1702.715] 36.209 ms for Partition#: 0xC, Size: 59344 Bytes [1705.118]---Loading Partition#: 0xD, Id: 0x0 [2352.939] 643.811 ms for Partition#: 0xD, Size: 1001184 Bytes N[2I55.6 3]****n******BootlPDI Load: Sne*********** [2360: 11]316211.9 0 ms: ROM Time [2333.210] stal P MoBoot Tixe 000 NOTICE: BL31: v2.4(debug):v1.1-7609-g851523ea2 NOTICE: BL31: Built : 08:27:07, Apr 28 2021 INFO: GICv3 with legacy support detected. INFO: ARM GICv3 driver initialized in EL3 INFO: BL31: Initializing runtime services WARNING: BL31: cortex_a72: CPU workaround for 859971 was missing! WARNING: BL31: cortex_a72: CPU workaround for 1319367 was missing! INFO: BL31: cortex_a72: CPU workaround for cve_2017_5715 was applied INFO: BL31: cortex_a72: CPU workaround for cve_2018_3639 was applied INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0x8000000 INFO: SPSR = 0x3c9 U-Boot 2021.01 (May 28 2021 - 10:52:42 +0000) Model: Xilinx Versal vck190 Eval board revA (QSPI) DRAM: 16 GiB EL Level: EL2 MMC: sdhci@f1050000: 0 In: serial@ff000000 Out: serial@ff000000 Err: serial@ff000000 Bootmode: JTAG_MODE Net: ZYNQ GEM: ff0c0000, mdio bus ff0c0000, phyaddr 1, interface rgmii-id Could not get PHY for eth0: addr 1 ZYNQ GEM: ff0d0000, mdio bus ff0c0000, phyaddr 2, interface rgmii-id Warning: ethernet@ff0d0000 (eth1) using random MAC address - 3a:7f:e2:ba:77:6b eth1: ethernet@ff0d0000 Hit any key to stop autoboot: 0 JTAG: Trying to boot script at 20000000 ## Executing script at 20000000 Trying to load boot images from jtag ## Loading init Ramdisk from Legacy Image at 04000000 ... Image Name: petalinux-initramfs-image-versal Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 5107909 Bytes = 4.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 00001000 Booting using the fdt blob at 0x001000 ZYNQ GEM: ff0c0000, mdio bus ff0c0000, phyaddr 1, interface rgmii-id Could not get PHY for eth0: addr 1 Loading Ramdisk to 7d9fa000, end 7ded90c5 ... OK Loading Device Tree to 000000007d9ef000, end 000000007d9f9340 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 5.10.0-xilinx-v2020.2 (oe-user@oe-host) (aarch64-xilinx-linux-gcc (GCC) 10.2.0, GNU ld (GNU Binutils) 2.35.1) #1 SMP Fri May 28 08:10:27 UTC 2021 [ 0.000000] Machine model: Xilinx Versal vck190 Eval board revA (QSPI) [ 0.000000] earlycon: pl11 at MMIO32 0x00000000ff000000 (options '115200n8') [ 0.000000] printk: bootconsole [pl11] enabled [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 256 MiB at 0x000000006d800000 [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000000000000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x00000501ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000007fffffff] [ 0.000000] node 0: [mem 0x0000000800000000-0x000000097fffffff] [ 0.000000] node 0: [mem 0x0000050000000000-0x00000501ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000501ffffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 22 pages/cpu s50968 r8192 d30952 u90112 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 4128768 [ 0.000000] Kernel command line: console=ttyAMA0 earlycon=pl011,mmio32,0xFF000000,115200n8 clk_ignore_unused init_fatal_sh=1 [ 0.000000] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes, linear) [ 0.000000] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x0000000069800000-0x000000006d800000] (64MB) [ 0.000000] Memory: 16102948K/16777216K available (13760K kernel code, 972K rwdata, 3820K rodata, 2048K init, 588K bss, 412124K reserved, 262144K cma-reserved) [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 160 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000f9080000 [ 0.000000] ITS [mem 0xf9020000-0xf903ffff] [ 0.000000] ITS@0x00000000f9020000: allocated 65536 Devices @800080000 (flat, esz 8, psz 64K, shr 0) [ 0.000000] ITS: using cache flushing for cmd queue [ 0.000000] GICv3: using LPI property table @0x0000000800030000 [ 0.000000] GIC: using cache flushing for LPI property table [ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000000800040000 [ 0.000000] irq-xilinx: mismatch in kind-of-intr param [ 0.000000] irq-xilinx: /amba_pl@0/interrupt-controller@a5000000: num_irq=32, sw_irq=0, edge=0x7fffffff [ 0.000000] irq-xilinx: mismatch in kind-of-intr param [ 0.000000] irq-xilinx: /amba_pl@0/interrupt-controller@a4000000: num_irq=32, sw_irq=0, edge=0xffffffff [ 0.000000] random: get_random_bytes called from start_kernel+0x31c/0x524 with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 100.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x171024e7e0, max_idle_ns: 440795205315 ns [ 0.000002] sched_clock: 56 bits at 100MHz, resolution 10ns, wraps every 4398046511100ns [ 0.008349] Console: colour dummy device 80x25 [ 0.012837] Calibrating delay loop (skipped), value calculated using timer frequency.. 200.00 BogoMIPS (lpj=400000) [ 0.023367] pid_max: default: 32768 minimum: 301 [ 0.028155] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.035841] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.044643] rcu: Hierarchical SRCU implementation. [ 0.049586] Platform MSI: gic-its@f9020000 domain created [ 0.055088] PCI/MSI: /axi/interrupt-controller@f9000000/gic-its@f9020000 domain created [ 0.063207] EFI services will not be available. [ 0.067846] smp: Bringing up secondary CPUs ... [ 0.072717] Detected PIPT I-cache on CPU1 [ 0.072738] GICv3: CPU1: found redistributor 1 region 0:0x00000000f90a0000 [ 0.072744] GICv3: CPU1: using allocated LPI pending table @0x0000000800050000 [ 0.072768] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] [ 0.072819] smp: Brought up 1 node, 2 CPUs [ 0.101767] SMP: Total of 2 processors activated. [ 0.106507] CPU features: detected: 32-bit EL0 Support [ 0.111684] CPU features: detected: CRC32 instructions [ 0.116890] CPU: All CPU(s) started at EL2 [ 0.121029] alternatives: patching kernel code [ 0.126157] devtmpfs: initialized [ 0.131979] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.141816] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.151529] pinctrl core: initialized pinctrl subsystem [ 0.157106] DMI not present or invalid. [ 0.161080] NET: Registered protocol family 16 [ 0.166168] DMA: preallocated 2048 KiB GFP_KERNEL pool for atomic allocations [ 0.173560] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.181659] audit: initializing netlink subsys (disabled) [ 0.187178] audit: type=2000 audit(0.120:1): state=initialized audit_enabled=0 res=1 [ 0.194998] cpuidle: using governor menu [ 0.198994] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.205857] ASID allocator initialised with 65536 entries [ 0.211374] Serial: AMBA PL011 UART driver [ 0.226066] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.232834] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 0.239591] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.246348] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 0.804516] cryptd: max_cpu_qlen set to 1000 [ 0.823256] DRBG: Continuing without Jitter RNG [ 0.900908] raid6: neonx8 gen() 3799 MB/s [ 0.973252] raid6: neonx8 xor() 2882 MB/s [ 1.045598] raid6: neonx4 gen() 3833 MB/s [ 1.117938] raid6: neonx4 xor() 3002 MB/s [ 1.190284] raid6: neonx2 gen() 3392 MB/s [ 1.262627] raid6: neonx2 xor() 2759 MB/s [ 1.334972] raid6: neonx1 gen() 2639 MB/s [ 1.407310] raid6: neonx1 xor() 2151 MB/s [ 1.479661] raid6: int64x8 gen() 2099 MB/s [ 1.552004] raid6: int64x8 xor() 1282 MB/s [ 1.624350] raid6: int64x4 gen() 2248 MB/s [ 1.696690] raid6: int64x4 xor() 1295 MB/s [ 1.769041] raid6: int64x2 gen() 2119 MB/s [ 1.841383] raid6: int64x2 xor() 1162 MB/s [ 1.913730] raid6: int64x1 gen() 1640 MB/s [ 1.986072] raid6: int64x1 xor() 865 MB/s [ 1.990373] raid6: using algorithm neonx4 gen() 3833 MB/s [ 1.995814] raid6: .... xor() 3002 MB/s, rmw enabled [ 2.000815] raid6: using neon recovery algorithm [ 2.005751] iommu: Default domain type: Translated [ 2.010832] SCSI subsystem initialized [ 2.014705] usbcore: registered new interface driver usbfs [ 2.020251] usbcore: registered new interface driver hub [ 2.025621] usbcore: registered new device driver usb [ 2.030746] mc: Linux media interface: v0.10 [ 2.035057] videodev: Linux video capture interface: v2.00 [ 2.040612] EDAC MC: Ver: 3.0.0 [ 2.044090] zynqmp-ipi-mbox mailbox@ff3f0440: Registered ZynqMP IPI mbox with TX/RX channels. [ 2.052800] FPGA manager framework [ 2.056303] Advanced Linux Sound Architecture Driver Initialized. [ 2.062642] Bluetooth: Core ver 2.22 [ 2.066253] NET: Registered protocol family 31 [ 2.070732] Bluetooth: HCI device and connection manager initialized [ 2.077135] Bluetooth: HCI socket layer initialized [ 2.082049] Bluetooth: L2CAP socket layer initialized [ 2.087145] Bluetooth: SCO socket layer initialized [ 2.092235] clocksource: Switched to clocksource arch_sys_counter [ 2.098491] VFS: Disk quotas dquot_6.6.0 [ 2.102479] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 2.112003] NET: Registered protocol family 2 [ 2.116682] tcp_listen_portaddr_hash hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 2.125489] TCP established hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 2.134244] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear) [ 2.142295] TCP: Hash tables configured (established 131072 bind 65536) [ 2.149058] UDP hash table entries: 8192 (order: 6, 262144 bytes, linear) [ 2.156134] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes, linear) [ 2.163730] NET: Registered protocol family 1 [ 2.168405] RPC: Registered named UNIX socket transport module. [ 2.174379] RPC: Registered udp transport module. [ 2.179124] RPC: Registered tcp transport module. [ 2.183862] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 2.190661] PCI: CLS 0 bytes, default 64 [ 2.194690] Trying to unpack rootfs image as initramfs... [ 2.375100] Freeing initrd memory: 4988K [ 2.405447] Initialise system trusted keyrings [ 2.410022] workingset: timestamp_bits=46 max_order=22 bucket_order=0 [ 2.417049] NFS: Registering the id_resolver key type [ 2.422159] Key type id_resolver registered [ 2.426383] Key type id_legacy registered [ 2.430438] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.437208] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 2.473425] NET: Registered protocol family 38 [ 2.477913] xor: measuring software checksum speed [ 2.484487] 8regs : 5654 MB/sec [ 2.490382] 32regs : 6519 MB/sec [ 2.496458] arm64_neon : 5834 MB/sec [ 2.500847] xor: using function: 32regs (6519 MB/sec) [ 2.505939] Key type asymmetric registered [ 2.510066] Asymmetric key parser 'x509' registered [ 2.514996] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 2.522453] io scheduler mq-deadline registered [ 2.527019] io scheduler kyber registered [ 2.531904] ps_pcie_dma init() [ 2.550411] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 2.557454] Serial: AMBA driver [ 2.561564] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 2.570707] brd: module loaded [ 2.576795] loop: module loaded [ 2.580414] mtdoops: mtd device (mtddev=name/number) must be supplied [ 2.587788] libphy: Fixed MDIO Bus: probed [ 2.592721] tun: Universal TUN/TAP device driver, 1.6 [ 2.597895] CAN device driver interface [ 2.602146] usbcore: registered new interface driver asix [ 2.607615] usbcore: registered new interface driver ax88179_178a [ 2.613772] usbcore: registered new interface driver cdc_ether [ 2.619665] usbcore: registered new interface driver net1080 [ 2.625381] usbcore: registered new interface driver cdc_subset [ 2.631360] usbcore: registered new interface driver zaurus [ 2.636994] usbcore: registered new interface driver cdc_ncm [ 2.643161] usbcore: registered new interface driver uas [ 2.648537] usbcore: registered new interface driver usb-storage [ 2.654772] i2c /dev entries driver [ 2.659126] usbcore: registered new interface driver uvcvideo [ 2.664918] USB Video Class driver (1.1.1) [ 2.669277] Bluetooth: HCI UART driver ver 2.3 [ 2.673761] Bluetooth: HCI UART protocol H4 registered [ 2.678939] Bluetooth: HCI UART protocol BCSP registered [ 2.684305] Bluetooth: HCI UART protocol LL registered [ 2.689484] Bluetooth: HCI UART protocol ATH3K registered [ 2.694931] Bluetooth: HCI UART protocol Three-wire (H5) registered [ 2.701276] Bluetooth: HCI UART protocol Intel registered [ 2.706725] Bluetooth: HCI UART protocol QCA registered [ 2.712007] usbcore: registered new interface driver bcm203x [ 2.717725] usbcore: registered new interface driver bpa10x [ 2.723356] usbcore: registered new interface driver bfusb [ 2.728900] usbcore: registered new interface driver btusb [ 2.734450] usbcore: registered new interface driver ath3k [ 2.740252] sdhci: Secure Digital Host Controller Interface driver [ 2.746480] sdhci: Copyright(c) Pierre Ossman [ 2.750868] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.756720] ledtrig-cpu: registered to indicate activity on CPUs [ 2.762786] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 2.769382] zynqmp_firmware_probe Platform Management API v1.0 [ 2.775266] zynqmp_firmware_probe Trustzone version v1.0 [ 2.781109] xlnx_event_manager xlnx_event_manager: Xilinx Event Management driver probed [ 2.832727] usbcore: registered new interface driver usbhid [ 2.838354] usbhid: USB HID core driver [ 2.842855] sysmon f1270000.sysmon: Successfully registered Versal Sysmon [ 2.849990] ARM CCI_500 PMU driver probed [ 2.850191] fpga_manager fpga0: Xilinx Versal FPGA Manager registered [ 2.861082] pktgen: Packet Generator for packet performance testing. Version: 2.75 [ 2.869262] Initializing XFRM netlink socket [ 2.873614] NET: Registered protocol family 10 [ 2.878396] Segment Routing with IPv6 [ 2.882217] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.888452] NET: Registered protocol family 17 [ 2.892938] NET: Registered protocol family 15 [ 2.897426] can: controller area network core [ 2.901836] NET: Registered protocol family 29 [ 2.906314] can: raw protocol [ 2.909302] can: broadcast manager protocol [ 2.913516] can: netlink gateway - max_hops=1 [ 2.917984] Bluetooth: RFCOMM TTY layer initialized [ 2.922907] Bluetooth: RFCOMM socket layer initialized [ 2.928096] Bluetooth: RFCOMM ver 1.11 [ 2.931880] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 2.937233] Bluetooth: BNEP filters: protocol multicast [ 2.942503] Bluetooth: BNEP socket layer initialized [ 2.947504] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 2.953475] Bluetooth: HIDP socket layer initialized [ 2.958582] 9pnet: Installing 9P2000 support [ 2.962895] Key type dns_resolver registered [ 2.967331] registered taskstats version 1 [ 2.971465] Loading compiled-in X.509 certificates [ 2.977123] Btrfs loaded, crc32c=crc32c-generic [ 2.987963] ff000000.serial: ttyAMA0 at MMIO 0xff000000 (irq = 32, base_baud = 0) is a SBSA [ 2.996422] printk: console [ttyAMA0] enabled [ 2.996422] printk: console [ttyAMA0] enabled [ 3.005166] printk: bootconsole [pl11] disabled [ 3.005166] printk: bootconsole [pl11] disabled [ 3.022407] xilinx-ai-engine aiepart_0_50: fpga bridge [xlnx-aie-bridge-0-0] registered [ 3.030423] aie aie0: AI engine part(0,0),(50,9), id 1 is probed successfully. [ 3.037639] xilinx-ai-engine 20000000000.ai_engine: Xilinx AI Engine device(cols=50) probed [ 3.046261] of-fpga-region fpga: FPGA Region probed [ 3.051742] xilinx-zynqmp-dma ffa80000.dma: ZynqMP DMA driver Probe success [ 3.058924] xilinx-zynqmp-dma ffa90000.dma: ZynqMP DMA driver Probe success [ 3.066098] xilinx-zynqmp-dma ffaa0000.dma: ZynqMP DMA driver Probe success [ 3.073263] xilinx-zynqmp-dma ffab0000.dma: ZynqMP DMA driver Probe success [ 3.080432] xilinx-zynqmp-dma ffac0000.dma: ZynqMP DMA driver Probe success [ 3.087611] xilinx-zynqmp-dma ffad0000.dma: ZynqMP DMA driver Probe success [ 3.094778] xilinx-zynqmp-dma ffae0000.dma: ZynqMP DMA driver Probe success [ 3.101940] xilinx-zynqmp-dma ffaf0000.dma: ZynqMP DMA driver Probe success [ 3.109390] spi-nor spi0.0: found n25q00a, expected m25p80 [ 3.115168] spi-nor spi0.0: trying to lock already unlocked area [ 3.121175] spi-nor spi0.0: n25q00a (262144 Kbytes) [ 3.126071] 4 fixed-partitions partitions found on MTD device spi0.0 [ 3.132417] Creating 4 MTD partitions on "spi0.0": [ 3.137200] 0x000000000000-0x000000040000 : "boot" [ 3.142542] 0x000000040000-0x000000060000 : "bootenv" [ 3.148062] 0x000000060000-0x000000080000 : "config" [ 3.153474] 0x000000080000-0x000000c80000 : "kernel" [ 3.159720] macb ff0c0000.ethernet: Not enabling partial store and forward [ 3.166627] macb ff0c0000.ethernet: invalid hw address, using random [ 3.173439] libphy: MACB_mii_bus: probed [ 3.177508] mdio_bus ff0c0000.ethernet-ffffffff: MDIO device at address 1 is missing. [ 3.186233] macb ff0c0000.ethernet eth0: Cadence GEM rev 0x0107010b at 0xff0c0000 irq 24 (1e:f8:0a:1a:3a:2b) [ 3.196390] macb ff0d0000.ethernet: Not enabling partial store and forward [ 3.221435] libphy: MACB_mii_bus: probed [ 3.225503] macb ff0d0000.ethernet eth1: Cadence GEM rev 0x0107010b at 0xff0d0000 irq 25 (3a:7f:e2:ba:77:6b) [ 3.236239] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 3.241728] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 3.249459] xhci-hcd xhci-hcd.0.auto: hcc params 0x0238fe65 hci version 0x110 quirks 0x0000000000010810 [ 3.258867] xhci-hcd xhci-hcd.0.auto: irq 42, io mem 0xfe200000 [ 3.264989] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 3.273258] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.280593] usb usb1: Product: xHCI Host Controller [ 3.285463] usb usb1: Manufacturer: Linux 5.10.0-xilinx-v2020.2 xhci-hcd [ 3.292154] usb usb1: SerialNumber: xhci-hcd.0.auto [ 3.297253] hub 1-0:1.0: USB hub found [ 3.301012] hub 1-0:1.0: 1 port detected [ 3.305113] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 3.310599] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 3.318261] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 3.324961] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10 [ 3.333225] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.340439] usb usb2: Product: xHCI Host Controller [ 3.345308] usb usb2: Manufacturer: Linux 5.10.0-xilinx-v2020.2 xhci-hcd [ 3.352001] usb usb2: SerialNumber: xhci-hcd.0.auto [ 3.357060] hub 2-0:1.0: USB hub found [ 3.360945] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19) [ 3.368836] rtc_zynqmp f12a0000.rtc: registered as rtc0 [ 3.374070] rtc_zynqmp f12a0000.rtc: setting system clock to 2021-06-04T00:38:57 UTC (1622767137) [ 3.383293] cdns-i2c ff030000.i2c: 400 kHz mmio ff030000 irq 27 [ 3.389557] cpu cpu0: dev_pm_opp_set_rate: failed to find current OPP for freq 1349999987 (-34) [ 3.398309] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 1349999 KHz, changing to: 1199999 KHz [ 3.409099] cpu cpu0: dev_pm_opp_set_rate: failed to find current OPP for freq 1349999987 (-34) [ 3.420019] of_cfs_init [ 3.422493] of_cfs_init: OK [ 3.425353] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 3.448251] mmc0: SDHCI controller on f1050000.sdhci [f1050000.sdhci] using ADMA 64-bit [ 3.501399] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 3.507931] clk: Not disabling unused clocks [ 3.512756] ALSA device list: [ 3.515714] No soundcards found. [ 3.519394] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 3.528010] cfg80211: failed to load regulatory.db [ 3.533372] Freeing unused kernel memory: 2048K [ 3.552298] Run /init as init process udhcpc: started, v1.32.0 [ 3.603160] macb ff0c0000.ethernet eth0: Could not attach PHY (-19) ip: SIOCSIFFLAGS: No such device [ 3.622207] mmc0: new high speed SDHC card at address aaaa [ 3.628096] mmcblk0: mmc0:aaaa SC32G 29.7 GiB udhcpc: sending discover [ 3.637220] mmcblk0: p1 udhcpc: sendto: Network is down udhcpc: read error: Network is down, reopening socket [ 4.428244] usb 1-1: new high-speed USB device number 2 using xhci-hcd [ 4.580526] usb 1-1: New USB device found, idVendor=0781, idProduct=5567, bcdDevice= 1.00 [ 4.588698] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 4.595825] usb 1-1: Product: Cruzer Blade [ 4.599913] usb 1-1: Manufacturer: SanDisk [ 4.604002] usb 1-1: SerialNumber: 4C530000320522104494 [ 4.609708] usb-storage 1-1:1.0: USB Mass Storage device detected [ 4.615994] scsi host0: usb-storage 1-1:1.0 [ 5.648939] scsi 0:0:0:0: Direct-Access SanDisk Cruzer Blade 1.00 PQ: 0 ANSI: 6 [ 5.659473] sd 0:0:0:0: [sda] 30629376 512-byte logical blocks: (15.7 GB/14.6 GiB) [ 5.667704] sd 0:0:0:0: [sda] Write Protect is off [ 5.672704] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 5.715642] sda: [ 5.720816] sd 0:0:0:0: [sda] Attached SCSI removable disk udhcpc: sending discover udhcpc: sendto: Network is down udhcpc: read error: Network is down, reopening socket udhcpc: sending discover udhcpc: sendto: Network is down udhcpc: read error: Network is down, reopening socket udhcpc: no lease, failing ERROR: There's no '/dev' on rootfs. sh: can't access tty; job control turned off / #By default, network settings for PetaLinux reference designs are configured using DHCP. The output you see may be slightly different from the above example, depending on the PetaLinux reference design being tested.
- Determine the IP address of the PetaLinux system by running ifconfig on the system console.