You can boot a PetaLinux image on hardware
using an SD card or pre-built wic image after mounting the SD card.
Steps to Flash and Boot the PetaLinux Images Manually
- Copy the following files from <plnx-proj-root>/pre-built/linux/images/ into the root directory of
the first partition, which is in FAT32 format in the SD card:
- BOOT.BIN
- image.ub
- boot.scr
- Extract the rootfs.tar.gz folder into the ext4 partition of the SD card.
- Connect the serial port on the board to your workstation.
- Open a console on the workstation and start the preferred serial communication program (For example: kermit, minicom, gtkterm) with the baud rate set to 115200 on that console.
- Power off the board.
- Set the boot mode of the board to SD boot. Refer to the board documentation for details.
- Plug the SD card into the board.
- Power on the board.
- A boot message displays on the serial console.
Steps to Flash and Boot PetaLinux Image Using Prebuilt WIC Image
- Go to the <plnx-proj-root>/pre-built/linux/images/ directory. For example, cd prebuilt/linux/images.
- Extract the petalinux-sdimage.wic.xz
file with the
xzcommand. For example,xz -d petalinux-sdimage.wic.xzNote: If xz package is not installed in your build machine, use the prebuilt xz binary from $PETALINUX/components/yocto/buildtools/sysroots/x86_64-petalinux-linux/usr/bin/xz - Flash the extracted petalinux-sdimage.wic image into the SD card.
- Flash the wic image in Linux
- To flash the wic image to SD card in Linux machines, connect the
SD card to the host system and use the
ddcommand:dd if=petalinux-sdimage.wic of=/dev/sd<X> conv=fsyncNote: You need sudo access to do this.
- Flash the wic image in Windows
- To flash the wic image to the SD card in Windows, you can use any
of the following:
- BalenaEtcher tool
- Win32DiskImager
- Insert the SD card into the board and boot the system.
- Connect the serial port on the board to your workstation.
- Open a console on the workstation and start the preferred serial communication program (For example: kermit, minicom, gtkterm) with the baud rate set to 115200 on that console.
- Power off the board.
- Set the boot mode of the board to SD boot. Refer to the board documentation for details.
- Plug the SD card into the board.
- Power on the board. A boot message similar to the following displays on the serial console:
Tip: To stop
auto-boot, hit any key when you see a similar message on the console:
Hit any key to stop autoboot.
[430.184]Xilinx Versal Platform Loader and Manager
[434.702]Release 2021.1 May 31 2021 - 18:37:19
[439.133]Platform Version: v2.0 PMC: v2.0, PS: v2.0
[443.650]BOOTMODE: 0xE, MULTIBOOT: 0xF0000000
[447.656]****************************************
[452.043] 50.978 ms for Partition#: 0x1, Size: 2288 Bytes
[457.030]---Loading Partition#: 0x2, Id: 0x0
[463.646] 2.662 ms for Partition#: 0x2, Size: 48 Bytes
[465.726]---Loading Partition#: 0x3, Id: 0x0
[476.923] 7.243 ms for Partition#: 0x3, Size: 59280 Bytes
[479.168]---Loading Partition#: 0x4, Id: 0x0
[483.785] 0.663 ms for Partition#: 0x4, Size: 2640 Bytes
[488.032]---Loading Partition#: 0x5, Id: 0x0
[494.890] 2.905 ms for Partition#: 0x5, Size: 3440 Bytes
[497.050]---Loading Partition#: 0x6, Id: 0x0
[501.020] 0.018 ms for Partition#: 0x6, Size: 80 Bytes
PSM Firmware version: 2021.1 [Build: May 31 2021 18:37:19 ]
[511.042]+++Loading Image#: 0x2, Name: pl_cfi, Id: 0x18700000
[516.395]---Loading Partition#: 0x7, Id: 0x3
[719.051] 198.699 ms for Partition#: 0x7, Size: 1304480 Bytes
[721.640]---Loading Partition#: 0x8, Id: 0x5
[876.102] 150.506 ms for Partition#: 0x8, Size: 933344 Bytes
[878.647]+++Loading Image#: 0x3, Name: aie_subsys, Id: 0x0421C005
[884.320]---Loading Partition#: 0x9, Id: 0x7
[893.552] 5.276 ms for Partition#: 0x9, Size: 352 Bytes
[895.671]+++Loading Image#: 0x4, Name: fpd, Id: 0x0420C003
[900.745]---Loading Partition#: 0xA, Id: 0x8
[907.520] 2.819 ms for Partition#: 0xA, Size: 1040 Bytes
[909.944]+++Loading Image#: 0x5, Name: apu_subsystem, Id: 0x1C000000
[915.656]---Loading Partition#: 0xB, Id: 0x0
[925.484] 5.870 ms for Partition#: 0xB, Size: 29520 Bytes
[927.734]---Loading Partition#: 0xC, Id: 0x0
[938.507] 6.813 ms for Partition#: 0xC, Size: 59344 Bytes
[940.756]---Loading Partition#: 0xD, Id: 0x0
[1057.431] 112.718 ms for Partition#: 0xD, Size: 1001184 Bytes
***T**:1 7]****n**** *Booi PDI Loada Donl****
I[1:67.443]Totnl PLu Booo Timt 0
000000
NOTICE: BL31: v2.4(debug):v1.1-7609-g851523ea2
NOTICE: BL31: Built : 08:27:07, Apr 28 2021
INFO: GICv3 with legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: BL31: Initializing runtime services
WARNING: BL31: cortex_a72: CPU workaround for 859971 was missing!
WARNING: BL31: cortex_a72: CPU workaround for 1319367 was missing!
INFO: BL31: cortex_a72: CPU workaround for cve_2017_5715 was applied
INFO: BL31: cortex_a72: CPU workaround for cve_2018_3639 was applied
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x8000000
INFO: SPSR = 0x3c9
U-Boot 2021.01 (May 28 2021 - 10:52:42 +0000)
Model: Xilinx Versal vck190 Eval board revA (QSPI)
DRAM: 16 GiB
EL Level: EL2
MMC: sdhci@f1050000: 0
Loading Environment from FAT... *** Warning - bad CRC, using default environment
In: serial@ff000000
Out: serial@ff000000
Err: serial@ff000000
Bootmode: LVL_SHFT_SD_MODE1
Net:
ZYNQ GEM: ff0c0000, mdio bus ff0c0000, phyaddr 1, interface rgmii-id
Warning: ethernet@ff0c0000 (eth0) using random MAC address - 1e:e1:11:40:ef:d6
eth0: ethernet@ff0c0000
ZYNQ GEM: ff0d0000, mdio bus ff0c0000, phyaddr 2, interface rgmii-id
Warning: ethernet@ff0d0000 (eth1) using random MAC address - f2:85:0f:5f:a3:5f
, eth1: ethernet@ff0d0000
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot.scr
2594 bytes read in 13 ms (194.3 KiB/s)
## Executing script at 20000000
Trying to load boot images from mmc0
14374372 bytes read in 1058 ms (13 MiB/s)
## Loading kernel from FIT Image at 10000000 ...
Using 'conf-system-top.dtb' configuration
Trying 'kernel-1' kernel subimage
Description: Linux kernel
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x100000f8
Data Size: 9234816 Bytes = 8.8 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x00080000
Entry Point: 0x00080000
Hash algo: sha256
Hash value: 5b46d9864f6d5cb91e6feb01293ccbe2e0a126afe9e55ac6bc124be877a2a758
Verifying Hash Integrity ... sha256+ OK
## Loading ramdisk from FIT Image at 10000000 ...
Using 'conf-system-top.dtb' configuration
Trying 'ramdisk-1' ramdisk subimage
Description: petalinux-initramfs-image
Type: RAMDisk Image
Compression: uncompressed
Data Start: 0x108d5fa0
Data Size: 5107915 Bytes = 4.9 MiB
Architecture: AArch64
OS: Linux
Load Address: unavailable
Entry Point: unavailable
Hash algo: sha256
Hash value: 095c3689da7cc27094ee64069f1a9419a6920ecf5f888dbdb8a8641e74e404fa
Verifying Hash Integrity ... sha256+ OK
## Loading fdt from FIT Image at 10000000 ...
Using 'conf-system-top.dtb' configuration
Trying 'fdt-system-top.dtb' fdt subimage
Description: Flattened Device Tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x108ceb88
Data Size: 29505 Bytes = 28.8 KiB
Architecture: AArch64
Hash algo: sha256
Hash value: 4ea39107d5bca89d4c3efd0984bf2191b0ada397a25efa31d340c747b5d66046
Verifying Hash Integrity ... sha256+ OK
Booting using the fdt blob at 0x108ceb88
Uncompressing Kernel Image
Loading Ramdisk to 7d9f9000, end 7ded80cb ... OK
Loading Device Tree to 000000007d9ee000, end 000000007d9f8340 ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083]
[ 0.000000] Linux version 5.10.0-xilinx-v2020.2 (oe-user@oe-host) (aarch64-xilinx-linux-gcc (GCC) 10.2.0, GNU ld (GNU Binutils) 2.35.1) #1 SMP Fri May 28 08:10:27 UTC 2021
[ 0.000000] Machine model: Xilinx Versal vck190 Eval board revA (QSPI)
[ 0.000000] earlycon: pl11 at MMIO32 0x00000000ff000000 (options '115200n8')
[ 0.000000] printk: bootconsole [pl11] enabled
[ 0.000000] efi: UEFI not found.
[ 0.000000] [Firmware Bug]: Kernel image misaligned at boot, please fix your bootloader!
[ 0.000000] cma: Reserved 256 MiB at 0x000000006d800000
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000000000000-0x00000000ffffffff]
[ 0.000000] Normal [mem 0x0000000100000000-0x00000501ffffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000007fffffff]
[ 0.000000] node 0: [mem 0x0000000800000000-0x000000097fffffff]
[ 0.000000] node 0: [mem 0x0000050000000000-0x00000501ffffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000501ffffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.2
[ 0.000000] percpu: Embedded 22 pages/cpu s50968 r8192 d30952 u90112
[ 0.000000] Detected PIPT I-cache on CPU0
[ 0.000000] CPU features: detected: GIC system register CPU interface
[ 0.000000] CPU features: detected: Spectre-v2
[ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 4128768
[ 0.000000] Kernel command line: console=ttyAMA0 earlycon=pl011,mmio32,0xFF000000,115200n8 clk_ignore_unused init_fatal_sh=1
[ 0.000000] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] software IO TLB: mapped [mem 0x0000000069800000-0x000000006d800000] (64MB)
[ 0.000000] Memory: 16102944K/16777216K available (13760K kernel code, 972K rwdata, 3820K rodata, 2048K init, 588K bss, 412128K reserved, 262144K cma-reserved)
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: 160 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] GICv3: Distributor has no Range Selector support
[ 0.000000] GICv3: 16 PPIs implemented
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000f9080000
[ 0.000000] ITS [mem 0xf9020000-0xf903ffff]
[ 0.000000] ITS@0x00000000f9020000: allocated 65536 Devices @800080000 (flat, esz 8, psz 64K, shr 0)
[ 0.000000] ITS: using cache flushing for cmd queue
[ 0.000000] GICv3: using LPI property table @0x0000000800030000
[ 0.000000] GIC: using cache flushing for LPI property table
[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000000800040000
[ 0.000000] irq-xilinx: mismatch in kind-of-intr param
[ 0.000000] irq-xilinx: /amba_pl@0/interrupt-controller@a5000000: num_irq=32, sw_irq=0, edge=0x7fffffff
[ 0.000000] irq-xilinx: mismatch in kind-of-intr param
[ 0.000000] irq-xilinx: /amba_pl@0/interrupt-controller@a4000000: num_irq=32, sw_irq=0, edge=0xffffffff
[ 0.000000] random: get_random_bytes called from start_kernel+0x31c/0x524 with crng_init=0
[ 0.000000] arch_timer: cp15 timer(s) running at 100.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x171024e7e0, max_idle_ns: 440795205315 ns
[ 0.000002] sched_clock: 56 bits at 100MHz, resolution 10ns, wraps every 4398046511100ns
[ 0.008347] Console: colour dummy device 80x25
[ 0.012837] Calibrating delay loop (skipped), value calculated using timer frequency.. 200.00 BogoMIPS (lpj=400000)
[ 0.023359] pid_max: default: 32768 minimum: 301
[ 0.028147] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 0.035831] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 0.044631] rcu: Hierarchical SRCU implementation.
[ 0.049574] Platform MSI: gic-its@f9020000 domain created
[ 0.055074] PCI/MSI: /axi/interrupt-controller@f9000000/gic-its@f9020000 domain created
[ 0.063187] EFI services will not be available.
[ 0.067826] smp: Bringing up secondary CPUs ...
[ 0.072702] Detected PIPT I-cache on CPU1
[ 0.072724] GICv3: CPU1: found redistributor 1 region 0:0x00000000f90a0000
[ 0.072731] GICv3: CPU1: using allocated LPI pending table @0x0000000800050000
[ 0.072753] CPU1: Booted secondary processor 0x0000000001 [0x410fd083]
[ 0.072803] smp: Brought up 1 node, 2 CPUs
[ 0.101734] SMP: Total of 2 processors activated.
[ 0.106472] CPU features: detected: 32-bit EL0 Support
[ 0.111649] CPU features: detected: CRC32 instructions
[ 0.116857] CPU: All CPU(s) started at EL2
[ 0.120994] alternatives: patching kernel code
[ 0.126141] devtmpfs: initialized
[ 0.131959] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.141793] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.151510] pinctrl core: initialized pinctrl subsystem
[ 0.157087] DMI not present or invalid.
[ 0.161062] NET: Registered protocol family 16
[ 0.166141] DMA: preallocated 2048 KiB GFP_KERNEL pool for atomic allocations
[ 0.173534] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.181632] audit: initializing netlink subsys (disabled)
[ 0.187153] audit: type=2000 audit(0.120:1): state=initialized audit_enabled=0 res=1
[ 0.194967] cpuidle: using governor menu
[ 0.198958] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.205820] ASID allocator initialised with 65536 entries
[ 0.211339] Serial: AMBA PL011 UART driver
[ 0.226033] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[ 0.232797] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[ 0.239557] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.246312] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[ 0.804400] cryptd: max_cpu_qlen set to 1000
[ 0.823105] DRBG: Continuing without Jitter RNG
[ 0.900781] raid6: neonx8 gen() 3793 MB/s
[ 0.973123] raid6: neonx8 xor() 2882 MB/s
[ 1.045464] raid6: neonx4 gen() 3834 MB/s
[ 1.117804] raid6: neonx4 xor() 3002 MB/s
[ 1.190144] raid6: neonx2 gen() 3403 MB/s
[ 1.262485] raid6: neonx2 xor() 2759 MB/s
[ 1.334827] raid6: neonx1 gen() 2642 MB/s
[ 1.407167] raid6: neonx1 xor() 2151 MB/s
[ 1.479514] raid6: int64x8 gen() 2099 MB/s
[ 1.551856] raid6: int64x8 xor() 1282 MB/s
[ 1.624198] raid6: int64x4 gen() 2248 MB/s
[ 1.696538] raid6: int64x4 xor() 1295 MB/s
[ 1.768878] raid6: int64x2 gen() 2113 MB/s
[ 1.841219] raid6: int64x2 xor() 1162 MB/s
[ 1.913567] raid6: int64x1 gen() 1641 MB/s
[ 1.985908] raid6: int64x1 xor() 865 MB/s
[ 1.990206] raid6: using algorithm neonx4 gen() 3834 MB/s
[ 1.995644] raid6: .... xor() 3002 MB/s, rmw enabled
[ 2.000646] raid6: using neon recovery algorithm
[ 2.005580] iommu: Default domain type: Translated
[ 2.010648] SCSI subsystem initialized
[ 2.014520] usbcore: registered new interface driver usbfs
[ 2.020065] usbcore: registered new interface driver hub
[ 2.025430] usbcore: registered new device driver usb
[ 2.030554] mc: Linux media interface: v0.10
[ 2.034865] videodev: Linux video capture interface: v2.00
[ 2.040417] EDAC MC: Ver: 3.0.0
[ 2.043892] zynqmp-ipi-mbox mailbox@ff3f0440: Registered ZynqMP IPI mbox with TX/RX channels.
[ 2.052602] FPGA manager framework
[ 2.056107] Advanced Linux Sound Architecture Driver Initialized.
[ 2.062452] Bluetooth: Core ver 2.22
[ 2.066060] NET: Registered protocol family 31
[ 2.070536] Bluetooth: HCI device and connection manager initialized
[ 2.076940] Bluetooth: HCI socket layer initialized
[ 2.081854] Bluetooth: L2CAP socket layer initialized
[ 2.086949] Bluetooth: SCO socket layer initialized
[ 2.092051] clocksource: Switched to clocksource arch_sys_counter
[ 2.098305] VFS: Disk quotas dquot_6.6.0
[ 2.102288] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 2.111809] NET: Registered protocol family 2
[ 2.116488] tcp_listen_portaddr_hash hash table entries: 8192 (order: 5, 131072 bytes, linear)
[ 2.125288] TCP established hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 2.134036] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear)
[ 2.142085] TCP: Hash tables configured (established 131072 bind 65536)
[ 2.148840] UDP hash table entries: 8192 (order: 6, 262144 bytes, linear)
[ 2.155925] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes, linear)
[ 2.163520] NET: Registered protocol family 1
[ 2.168181] RPC: Registered named UNIX socket transport module.
[ 2.174153] RPC: Registered udp transport module.
[ 2.178890] RPC: Registered tcp transport module.
[ 2.183626] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 2.190422] PCI: CLS 0 bytes, default 64
[ 2.194450] Trying to unpack rootfs image as initramfs...
[ 2.374713] Freeing initrd memory: 4988K
[ 2.406038] Initialise system trusted keyrings
[ 2.410591] workingset: timestamp_bits=46 max_order=22 bucket_order=0
[ 2.417679] NFS: Registering the id_resolver key type
[ 2.422844] Key type id_resolver registered
[ 2.427062] Key type id_legacy registered
[ 2.431120] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 2.437888] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 2.473759] NET: Registered protocol family 38
[ 2.478246] xor: measuring software checksum speed
[ 2.484823] 8regs : 5654 MB/sec
[ 2.490718] 32regs : 6520 MB/sec
[ 2.496794] arm64_neon : 5834 MB/sec
[ 2.501182] xor: using function: 32regs (6520 MB/sec)
[ 2.506270] Key type asymmetric registered
[ 2.510394] Asymmetric key parser 'x509' registered
[ 2.515325] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 2.522779] io scheduler mq-deadline registered
[ 2.527341] io scheduler kyber registered
[ 2.532244] ps_pcie_dma init()
[ 2.550780] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 2.557821] Serial: AMBA driver
[ 2.561933] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 2.571071] brd: module loaded
[ 2.577160] loop: module loaded
[ 2.580774] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 2.588148] libphy: Fixed MDIO Bus: probed
[ 2.593058] tun: Universal TUN/TAP device driver, 1.6
[ 2.598228] CAN device driver interface
[ 2.602484] usbcore: registered new interface driver asix
[ 2.607950] usbcore: registered new interface driver ax88179_178a
[ 2.614102] usbcore: registered new interface driver cdc_ether
[ 2.619992] usbcore: registered new interface driver net1080
[ 2.625706] usbcore: registered new interface driver cdc_subset
[ 2.631684] usbcore: registered new interface driver zaurus
[ 2.637322] usbcore: registered new interface driver cdc_ncm
[ 2.643489] usbcore: registered new interface driver uas
[ 2.648866] usbcore: registered new interface driver usb-storage
[ 2.655101] i2c /dev entries driver
[ 2.659456] usbcore: registered new interface driver uvcvideo
[ 2.665246] USB Video Class driver (1.1.1)
[ 2.669606] Bluetooth: HCI UART driver ver 2.3
[ 2.674088] Bluetooth: HCI UART protocol H4 registered
[ 2.679266] Bluetooth: HCI UART protocol BCSP registered
[ 2.684630] Bluetooth: HCI UART protocol LL registered
[ 2.689804] Bluetooth: HCI UART protocol ATH3K registered
[ 2.695247] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 2.701585] Bluetooth: HCI UART protocol Intel registered
[ 2.707031] Bluetooth: HCI UART protocol QCA registered
[ 2.712313] usbcore: registered new interface driver bcm203x
[ 2.718027] usbcore: registered new interface driver bpa10x
[ 2.723654] usbcore: registered new interface driver bfusb
[ 2.729197] usbcore: registered new interface driver btusb
[ 2.734745] usbcore: registered new interface driver ath3k
[ 2.740538] sdhci: Secure Digital Host Controller Interface driver
[ 2.746769] sdhci: Copyright(c) Pierre Ossman
[ 2.751157] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.757006] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.763071] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
[ 2.769667] zynqmp_firmware_probe Platform Management API v1.0
[ 2.775553] zynqmp_firmware_probe Trustzone version v1.0
[ 2.781389] xlnx_event_manager xlnx_event_manager: Xilinx Event Management driver probed
[ 2.832884] usbcore: registered new interface driver usbhid
[ 2.838507] usbhid: USB HID core driver
[ 2.843004] sysmon f1270000.sysmon: Successfully registered Versal Sysmon
[ 2.850142] ARM CCI_500 PMU driver probed
[ 2.850348] fpga_manager fpga0: Xilinx Versal FPGA Manager registered
[ 2.861230] pktgen: Packet Generator for packet performance testing. Version: 2.75
[ 2.869407] Initializing XFRM netlink socket
[ 2.873761] NET: Registered protocol family 10
[ 2.878537] Segment Routing with IPv6
[ 2.882353] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 2.888566] NET: Registered protocol family 17
[ 2.893050] NET: Registered protocol family 15
[ 2.897535] can: controller area network core
[ 2.901939] NET: Registered protocol family 29
[ 2.906417] can: raw protocol
[ 2.909403] can: broadcast manager protocol
[ 2.913617] can: netlink gateway - max_hops=1
[ 2.918072] Bluetooth: RFCOMM TTY layer initialized
[ 2.922996] Bluetooth: RFCOMM socket layer initialized
[ 2.928185] Bluetooth: RFCOMM ver 1.11
[ 2.931962] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 2.937313] Bluetooth: BNEP filters: protocol multicast
[ 2.942581] Bluetooth: BNEP socket layer initialized
[ 2.947583] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 2.953552] Bluetooth: HIDP socket layer initialized
[ 2.958657] 9pnet: Installing 9P2000 support
[ 2.962970] Key type dns_resolver registered
[ 2.967417] registered taskstats version 1
[ 2.971550] Loading compiled-in X.509 certificates
[ 2.977197] Btrfs loaded, crc32c=crc32c-generic
[ 2.988043] ff000000.serial: ttyAMA0 at MMIO 0xff000000 (irq = 32, base_baud = 0) is a SBSA
[ 2.996499] printk: console [ttyAMA0] enabled
[ 2.996499] printk: console [ttyAMA0] enabled
[ 3.005241] printk: bootconsole [pl11] disabled
[ 3.005241] printk: bootconsole [pl11] disabled
[ 3.022481] xilinx-ai-engine aiepart_0_50: fpga bridge [xlnx-aie-bridge-0-0] registered
[ 3.030498] aie aie0: AI engine part(0,0),(50,9), id 1 is probed successfully.
[ 3.037714] xilinx-ai-engine 20000000000.ai_engine: Xilinx AI Engine device(cols=50) probed
[ 3.046321] of-fpga-region fpga: FPGA Region probed
[ 3.051813] xilinx-zynqmp-dma ffa80000.dma: ZynqMP DMA driver Probe success
[ 3.058992] xilinx-zynqmp-dma ffa90000.dma: ZynqMP DMA driver Probe success
[ 3.066165] xilinx-zynqmp-dma ffaa0000.dma: ZynqMP DMA driver Probe success
[ 3.073334] xilinx-zynqmp-dma ffab0000.dma: ZynqMP DMA driver Probe success
[ 3.080500] xilinx-zynqmp-dma ffac0000.dma: ZynqMP DMA driver Probe success
[ 3.087669] xilinx-zynqmp-dma ffad0000.dma: ZynqMP DMA driver Probe success
[ 3.094834] xilinx-zynqmp-dma ffae0000.dma: ZynqMP DMA driver Probe success
[ 3.101999] xilinx-zynqmp-dma ffaf0000.dma: ZynqMP DMA driver Probe success
[ 3.109451] spi-nor spi0.0: found n25q00a, expected m25p80
[ 3.115228] spi-nor spi0.0: trying to lock already unlocked area
[ 3.121235] spi-nor spi0.0: n25q00a (262144 Kbytes)
[ 3.126134] 4 fixed-partitions partitions found on MTD device spi0.0
[ 3.132479] Creating 4 MTD partitions on "spi0.0":
[ 3.137262] 0x000000000000-0x000000040000 : "boot"
[ 3.142596] 0x000000040000-0x000000060000 : "bootenv"
[ 3.148124] 0x000000060000-0x000000080000 : "config"
[ 3.153531] 0x000000080000-0x000000c80000 : "kernel"
[ 3.159745] macb ff0c0000.ethernet: Not enabling partial store and forward
[ 3.167127] libphy: MACB_mii_bus: probed
[ 3.172700] macb ff0c0000.ethernet eth0: Cadence GEM rev 0x0107010b at 0xff0c0000 irq 24 (1e:e1:11:40:ef:d6)
[ 3.182861] macb ff0d0000.ethernet: Not enabling partial store and forward
[ 3.207930] libphy: MACB_mii_bus: probed
[ 3.211952] macb ff0d0000.ethernet eth1: Cadence GEM rev 0x0107010b at 0xff0d0000 irq 25 (f2:85:0f:5f:a3:5f)
[ 3.222682] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 3.228179] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 3.235913] xhci-hcd xhci-hcd.0.auto: hcc params 0x0238fe65 hci version 0x110 quirks 0x0000000000010810
[ 3.245323] xhci-hcd xhci-hcd.0.auto: irq 42, io mem 0xfe200000
[ 3.251495] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 3.259761] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.266978] usb usb1: Product: xHCI Host Controller
[ 3.271847] usb usb1: Manufacturer: Linux 5.10.0-xilinx-v2020.2 xhci-hcd
[ 3.278539] usb usb1: SerialNumber: xhci-hcd.0.auto
[ 3.283638] hub 1-0:1.0: USB hub found
[ 3.287396] hub 1-0:1.0: 1 port detected
[ 3.291542] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 3.297031] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 3.304690] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 3.311376] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
[ 3.319639] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.326861] usb usb2: Product: xHCI Host Controller
[ 3.331731] usb usb2: Manufacturer: Linux 5.10.0-xilinx-v2020.2 xhci-hcd
[ 3.338422] usb usb2: SerialNumber: xhci-hcd.0.auto
[ 3.343480] hub 2-0:1.0: USB hub found
[ 3.347365] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 3.355252] rtc_zynqmp f12a0000.rtc: registered as rtc0
[ 3.360497] rtc_zynqmp f12a0000.rtc: setting system clock to 2020-04-16T18:26:53 UTC (1587061613)
[ 3.369735] cdns-i2c ff030000.i2c: 400 kHz mmio ff030000 irq 27
[ 3.375993] cpu cpu0: dev_pm_opp_set_rate: failed to find current OPP for freq 1349999987 (-34)
[ 3.384745] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 1349999 KHz, changing to: 1199999 KHz
[ 3.395534] cpu cpu0: dev_pm_opp_set_rate: failed to find current OPP for freq 1349999987 (-34)
[ 3.406407] of_cfs_init
[ 3.408886] of_cfs_init: OK
[ 3.411741] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 3.436060] mmc0: SDHCI controller on f1050000.sdhci [f1050000.sdhci] using ADMA 64-bit
[ 3.478801] mmc0: new high speed SDHC card at address aaaa
[ 3.484605] mmcblk0: mmc0:aaaa SC16G 14.8 GiB
[ 3.487445] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 3.495584] clk: Not disabling unused clocks
[ 3.499708] mmcblk0: p1
[ 3.500407] ALSA device list:
[ 3.505322] No soundcards found.
[ 3.508990] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 3.517604] cfg80211: failed to load regulatory.db
[ 3.522975] Freeing unused kernel memory: 2048K
[ 3.536107] Run /init as init process
udhcpc: started, v1.32.0
[ 3.604931] macb ff0c0000.ethernet eth0: PHY [ff0c0000.ethernet-ffffffff:01] driver [TI DP83867] (irq=POLL)
[ 3.614678] macb ff0c0000.ethernet eth0: configuring for phy/rgmii-id link mode
udhcpc: sending discover
[ 4.504060] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 4.656335] usb 1-1: New USB device found, idVendor=0781, idProduct=5567, bcdDevice= 1.00
[ 4.664508] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4.671635] usb 1-1: Product: Cruzer Blade
[ 4.675723] usb 1-1: Manufacturer: SanDisk
[ 4.679811] usb 1-1: SerialNumber: 4C530000220130209065
[ 4.685530] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 4.691807] scsi host0: usb-storage 1-1:1.0
[ 5.712756] scsi 0:0:0:0: Direct-Access SanDisk Cruzer Blade 1.00 PQ: 0 ANSI: 6
[ 5.723337] sd 0:0:0:0: [sda] 30031872 512-byte logical blocks: (15.4 GB/14.3 GiB)
[ 5.731610] sd 0:0:0:0: [sda] Write Protect is off
[ 5.736611] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 5.768842] sda:
[ 5.774428] sd 0:0:0:0: [sda] Attached SCSI removable disk
udhcpc: sending discover
[ 6.673314] macb ff0c0000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 6.681082] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
udhcpc: sending discover
udhcpc: sending select for 10.10.71.3
udhcpc: lease of 10.10.71.3 obtained, lease time 600
ERROR: There's no '/dev' on rootfs.
sh: can't access tty; job control turned off
/ #