BRAM_TDP_MACRO - 2021.2 English

Vivado Design Suite 7 Series FPGA and Zynq-7000 SoC Libraries Guide (UG953)

Document ID
UG953
Release Date
2021-10-22
Version
2021.2 English

Macro: True Dual Port RAM

Introduction

7 series FPGA devices contain several block RAM memories that can be configured as general-purpose 36 kb or 18 kb RAM/ROM memories. These block RAM memories offer fast and flexible storage of large amounts of on-chip data. Both read and write operations are fully synchronous to the supplied clock(s) of the component. However, READ and WRITE ports can operate fully independently and asynchronous to each other, accessing the same memory array. Byte-enable write operations are possible, and an optional output register can be used to reduce the clock-to-out times of the RAM.

Port Descriptions

Port Direction Width Function
DOA Output See Port Configuration table Data output bus addressed by ADDRA.
DOB Output See Port Configuration table Data output bus addressed by ADDRB.
DIA Input See Port Configuration table Data input bus addressed by ADDRA.
DIB Input See Port Configuration table Data input bus addressed by ADDRB.
ADDRA, ADDRB Input See Port Configuration table Address input buses for Port A, B.
WEA, WEB Input See Port Configuration table Write enable for Port A, B.
ENA, ENB Input 1 Write/Read enables for Port A, B.
RSTA, RSTB Input 1 Output registers synchronous reset for Port A, B.
REGCEA, REGCEB Input 1 Output register clock enable input for Port A, B (valid only when DO_REG=1).
CLKA, CLKB Input 1 Write/Read clock input for Port A, B.

Port Configuration

This unimacro is a parameterizable version of the primitive, and can be instantiated only. Use this table to correctly configure the unimacro to meet design needs.
WRITE_WIDTH_A/B- READ_WIDTH_A/B-      
DIA/DIB DOA/DOB BRAM_SIZE ADDRA/B WEA/B
36 - 19 36 - 19 36 Kb 10 4
18-10 11
9 - 5 12
4 - 3 13
2 14
1 15
18 - 10 36 - 19 36 Kb 11 2
18-10 11
9 - 5 12
4 - 3 13
2 14
1 15
9 - 5 36-19 36 Kb 12 1
18-10 12
9 - 5 12
4 - 3 13
2 14
1 15
4 - 3 36-19 36 Kb 13 1
18-10 13
9 - 5 13
4 - 3 13
2 14
1 15
2 36-19 36 Kb 14 1
18-10 14
9 - 5 14
4 - 3 14
2 14
1 15
1 36-19 36 Kb 15 1
18-10 15
9 - 5 15
4 - 3 15
2 15
1 15
18-10 18-10 18 Kb 10 2
9 - 5 11
4 - 3 12
2 13
1 14
9 - 5 18-10 18 Kb 11 1
9 - 5 11
4 - 3 12
2 13
1 14
4 - 3 18-10 18 Kb 12 1
9 - 5 12
4 - 3 12
2 13
1 14
2 18-10 18 Kb 13 1
9 - 5 13
4 - 3 13
2 13
1 14
1 18-10 18 Kb 14 1
9 - 5 14
4 - 3 14
2 14
1 14

Design Entry Method

This unimacro is a parameterizable version of the primitive, and can be instantiated only. Consult the Port Configuration section to correctly configure this element to meet your design needs.
Instantiation Yes
Inference No
IP Catalog No
Macro support Recommended

Available Attributes

Attribute(s) Type Allowed Values Default Description
BRAM_SIZE STRING "36Kb", "18Kb" "18Kb" Configures RAM as "36Kb" or "18Kb" memory.
DEVICE STRING "7SERIES" "7SERIES" Target hardware architecture.
DO_REG INTEGER 0, 1 0 A value of 1 enables to the output registers to the RAM enabling quicker clock-to-out from the RAM at the expense of an added clock cycle of read latency. A value of 0 allows a read in one clock cycle but will have slower clock to out timing.
INIT HEX Any 72-Bit Value All zeros Specifies the initial value on the output after configuration.
INIT_FILE STRING String representing file name and location. NONE Name of file containing initial values.
READ_WIDTH, WRITE_WIDTH INTEGER 1 - 72 36 Specifies the size of the DI and DO buses.
The following combinations are allowed:
  • READ_WIDTH = WRITE_WIDTH

  • If asymmetric, READ_WIDTH and WRITE_WIDTH must be in the ratio of 2, or must be values allowed by the unisim (1, 2, 4, 8, 9, 16, 18, 32, 36)

SIM_COLLISION _CHECK STRING "ALL","WARNING_ONLY","GENERATE_X_ONLY","NONE" "ALL"

Allows modification of the simulation behavior if a memory collision occurs. The output is affected as follows:

  • "ALL": Warning produced and affected outputs/memory location go unknown (X).

  • "WARNING_ONLY": Warning produced and affected outputs/memory retain last value.

  • "GENERATE_X_ONLY": No warning. However, affected outputs/memory go unknown (X).

  • "NONE": No warning and affected outputs/memory retain last value.

Note: Setting this to a value other than "ALL" can allow problems in the design go unnoticed during simulation. Care should be taken when changing the value of this attribute. Please see the Synthesis and Simulation Design Guide for more information.
SRVAL A, SRVAL_B HEX Any 72-Bit Value All zeros Specifies the output value of on the DO port upon the assertion of the synchronous reset (RST) signal.
INIT_00 to INIT_FF HEX Any 256-Bit Value All zeros Specifies the initial contents of the 16 Kb or 32 Kb data memory array.
INITP_00 to INITP_0F HEX Any 256-Bit Value All zeros Specifies the initial contents of the 2 Kb or 4 Kb parity data memory array.

VHDL Instantiation Template

Unless they already exist, copy the following four statements and paste them before the entity declaration.
Library UNISIM;
use UNISIM.vcomponents.all;
library UNIMACRO;
use unimacro.Vcomponents.all;

-- BRAM_TDP_MACRO: True Dual Port RAM
--                 7 Series
-- Xilinx HDL Language Template, version 2021.2

-- Note -  This Unimacro model assumes the port directions to be "downto".
--         Simulation of this model with "to" in the port directions could lead to erroneous results.

--------------------------------------------------------------------------
-- DATA_WIDTH_A/B | BRAM_SIZE | RAM Depth | ADDRA/B Width | WEA/B Width --
-- ===============|===========|===========|===============|=============--
--     19-36      |  "36Kb"   |    1024   |    10-bit     |    4-bit    --
--     10-18      |  "36Kb"   |    2048   |    11-bit     |    2-bit    --
--     10-18      |  "18Kb"   |    1024   |    10-bit     |    2-bit    --
--      5-9       |  "36Kb"   |    4096   |    12-bit     |    1-bit    --
--      5-9       |  "18Kb"   |    2048   |    11-bit     |    1-bit    --
--      3-4       |  "36Kb"   |    8192   |    13-bit     |    1-bit    --
--      3-4       |  "18Kb"   |    4096   |    12-bit     |    1-bit    --
--        2       |  "36Kb"   |   16384   |    14-bit     |    1-bit    --
--        2       |  "18Kb"   |    8192   |    13-bit     |    1-bit    --
--        1       |  "36Kb"   |   32768   |    15-bit     |    1-bit    --
--        1       |  "18Kb"   |   16384   |    14-bit     |    1-bit    --
--------------------------------------------------------------------------

BRAM_TDP_MACRO_inst : BRAM_TDP_MACRO
generic map (
   BRAM_SIZE => "18Kb", -- Target BRAM, "18Kb" or "36Kb"
   DEVICE => "7SERIES", -- Target Device: "VIRTEX5", "VIRTEX6", "7SERIES", "SPARTAN6"
   DOA_REG => 0, -- Optional port A output register (0 or 1)
   DOB_REG => 0, -- Optional port B output register (0 or 1)
   INIT_A => X"000000000", -- Initial values on A output port
   INIT_B => X"000000000", -- Initial values on B output port
   INIT_FILE => "NONE",
   READ_WIDTH_A => 0,   -- Valid values are 1-36 (19-36 only valid when BRAM_SIZE="36Kb")
   READ_WIDTH_B => 0,   -- Valid values are 1-36 (19-36 only valid when BRAM_SIZE="36Kb")
   SIM_COLLISION_CHECK => "ALL", -- Collision check enable "ALL", "WARNING_ONLY",
                                 -- "GENERATE_X_ONLY" or "NONE"
   SRVAL_A => X"000000000",   -- Set/Reset value for A port output
   SRVAL_B => X"000000000",   -- Set/Reset value for B port output
   WRITE_MODE_A => "WRITE_FIRST", -- "WRITE_FIRST", "READ_FIRST" or "NO_CHANGE"
   WRITE_MODE_B => "WRITE_FIRST", -- "WRITE_FIRST", "READ_FIRST" or "NO_CHANGE"
   WRITE_WIDTH_A => 0, -- Valid values are 1-36 (19-36 only valid when BRAM_SIZE="36Kb")
   WRITE_WIDTH_B => 0, -- Valid values are 1-36 (19-36 only valid when BRAM_SIZE="36Kb")
   -- The following INIT_xx declarations specify the initial contents of the RAM
   INIT_00 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_01 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_02 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_03 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_04 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_05 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_06 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_07 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_08 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_09 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_0A => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_0B => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_0C => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_0D => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_0E => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_0F => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_10 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_11 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_12 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_13 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_14 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_15 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_16 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_17 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_18 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_19 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_1A => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_1B => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_1C => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_1D => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_1E => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_1F => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_20 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_21 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_22 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_23 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_24 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_25 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_26 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_27 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_28 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_29 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_2A => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_2B => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_2C => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_2D => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_2E => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_2F => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_30 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_31 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_32 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_33 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_34 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_35 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_36 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_37 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_38 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_39 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_3A => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_3B => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_3C => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_3D => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_3E => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_3F => X"0000000000000000000000000000000000000000000000000000000000000000",

   -- The next set of INIT_xx are valid when configured as 36Kb
   INIT_40 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_41 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_42 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_43 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_44 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_45 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_46 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_47 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_48 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_49 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_4A => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_4B => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_4C => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_4D => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_4E => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_4F => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_50 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_51 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_52 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_53 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_54 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_55 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_56 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_57 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_58 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_59 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_5A => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_5B => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_5C => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_5D => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_5E => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_5F => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_60 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_61 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_62 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_63 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_64 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_65 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_66 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_67 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_68 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_69 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_6A => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_6B => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_6C => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_6D => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_6E => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_6F => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_70 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_71 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_72 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_73 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_74 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_75 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_76 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_77 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_78 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_79 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_7A => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_7B => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_7C => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_7D => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_7E => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_7F => X"0000000000000000000000000000000000000000000000000000000000000000",

   -- The next set of INITP_xx are for the parity bits
   INITP_00 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INITP_01 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INITP_02 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INITP_03 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INITP_04 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INITP_05 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INITP_06 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INITP_07 => X"0000000000000000000000000000000000000000000000000000000000000000",

   -- The next set of INIT_xx are valid when configured as 36Kb
   INITP_08 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INITP_09 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INITP_0A => X"0000000000000000000000000000000000000000000000000000000000000000",
   INITP_0B => X"0000000000000000000000000000000000000000000000000000000000000000",
   INITP_0C => X"0000000000000000000000000000000000000000000000000000000000000000",
   INITP_0D => X"0000000000000000000000000000000000000000000000000000000000000000",
   INITP_0E => X"0000000000000000000000000000000000000000000000000000000000000000",
   INITP_0F => X"0000000000000000000000000000000000000000000000000000000000000000")
port map (
   DOA => DOA,       -- Output port-A data, width defined by READ_WIDTH_A parameter
   DOB => DOB,       -- Output port-B data, width defined by READ_WIDTH_B parameter
   ADDRA => ADDRA,   -- Input port-A address, width defined by Port A depth
   ADDRB => ADDRB,   -- Input port-B address, width defined by Port B depth
   CLKA => CLKA,     -- 1-bit input port-A clock
   CLKB => CLKB,     -- 1-bit input port-B clock
   DIA => DIA,       -- Input port-A data, width defined by WRITE_WIDTH_A parameter
   DIB => DIB,       -- Input port-B data, width defined by WRITE_WIDTH_B parameter
   ENA => ENA,       -- 1-bit input port-A enable
   ENB => ENB,       -- 1-bit input port-B enable
   REGCEA => REGCEA, -- 1-bit input port-A output register enable
   REGCEB => REGCEB, -- 1-bit input port-B output register enable
   RSTA => RSTA,     -- 1-bit input port-A reset
   RSTB => RSTB,     -- 1-bit input port-B reset
   WEA => WEA,       -- Input port-A write enable, width defined by Port A depth
   WEB => WEB        -- Input port-B write enable, width defined by Port B depth
);

-- End of BRAM_TDP_MACRO_inst instantiation

Verilog Instantiation Template


// BRAM_TDP_MACRO: True Dual Port RAM
//                 7 Series
// Xilinx HDL Language Template, version 2021.2

//////////////////////////////////////////////////////////////////////////
// DATA_WIDTH_A/B | BRAM_SIZE | RAM Depth | ADDRA/B Width | WEA/B Width //
// ===============|===========|===========|===============|=============//
//     19-36      |  "36Kb"   |    1024   |    10-bit     |    4-bit    //
//     10-18      |  "36Kb"   |    2048   |    11-bit     |    2-bit    //
//     10-18      |  "18Kb"   |    1024   |    10-bit     |    2-bit    //
//      5-9       |  "36Kb"   |    4096   |    12-bit     |    1-bit    //
//      5-9       |  "18Kb"   |    2048   |    11-bit     |    1-bit    //
//      3-4       |  "36Kb"   |    8192   |    13-bit     |    1-bit    //
//      3-4       |  "18Kb"   |    4096   |    12-bit     |    1-bit    //
//        2       |  "36Kb"   |   16384   |    14-bit     |    1-bit    //
//        2       |  "18Kb"   |    8192   |    13-bit     |    1-bit    //
//        1       |  "36Kb"   |   32768   |    15-bit     |    1-bit    //
//        1       |  "18Kb"   |   16384   |    14-bit     |    1-bit    //
//////////////////////////////////////////////////////////////////////////

BRAM_TDP_MACRO #(
   .BRAM_SIZE("18Kb"), // Target BRAM: "18Kb" or "36Kb"
   .DEVICE("7SERIES"), // Target device: "7SERIES"
   .DOA_REG(0),        // Optional port A output register (0 or 1)
   .DOB_REG(0),        // Optional port B output register (0 or 1)
   .INIT_A(36'h0000000),  // Initial values on port A output port
   .INIT_B(36'h00000000), // Initial values on port B output port
   .INIT_FILE ("NONE"),
   .READ_WIDTH_A (0),   // Valid values are 1-36 (19-36 only valid when BRAM_SIZE="36Kb")
   .READ_WIDTH_B (0),   // Valid values are 1-36 (19-36 only valid when BRAM_SIZE="36Kb")
   .SIM_COLLISION_CHECK ("ALL"), // Collision check enable "ALL", "WARNING_ONLY",
                                 //   "GENERATE_X_ONLY" or "NONE"
   .SRVAL_A(36'h00000000), // Set/Reset value for port A output
   .SRVAL_B(36'h00000000), // Set/Reset value for port B output
   .WRITE_MODE_A("WRITE_FIRST"), // "WRITE_FIRST", "READ_FIRST", or "NO_CHANGE"
   .WRITE_MODE_B("WRITE_FIRST"), // "WRITE_FIRST", "READ_FIRST", or "NO_CHANGE"
   .WRITE_WIDTH_A(0), // Valid values are 1-36 (19-36 only valid when BRAM_SIZE="36Kb")
   .WRITE_WIDTH_B(0), // Valid values are 1-36 (19-36 only valid when BRAM_SIZE="36Kb")
   .INIT_00(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_01(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_02(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_03(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_04(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_05(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_06(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_07(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_08(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_09(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_0A(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_0B(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_0C(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_0D(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_0E(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_0F(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_10(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_11(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_12(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_13(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_14(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_15(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_16(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_17(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_18(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_19(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_1A(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_1B(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_1C(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_1D(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_1E(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_1F(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_20(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_21(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_22(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_23(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_24(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_25(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_26(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_27(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_28(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_29(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_2A(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_2B(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_2C(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_2D(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_2E(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_2F(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_30(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_31(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_32(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_33(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_34(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_35(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_36(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_37(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_38(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_39(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_3A(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_3B(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_3C(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_3D(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_3E(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_3F(256'h0000000000000000000000000000000000000000000000000000000000000000),

   // The next set of INIT_xx are valid when configured as 36Kb
   .INIT_40(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_41(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_42(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_43(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_44(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_45(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_46(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_47(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_48(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_49(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_4A(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_4B(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_4C(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_4D(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_4E(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_4F(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_50(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_51(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_52(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_53(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_54(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_55(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_56(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_57(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_58(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_59(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_5A(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_5B(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_5C(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_5D(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_5E(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_5F(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_60(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_61(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_62(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_63(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_64(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_65(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_66(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_67(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_68(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_69(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_6A(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_6B(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_6C(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_6D(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_6E(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_6F(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_70(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_71(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_72(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_73(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_74(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_75(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_76(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_77(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_78(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_79(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_7A(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_7B(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_7C(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_7D(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_7E(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_7F(256'h0000000000000000000000000000000000000000000000000000000000000000),

   // The next set of INITP_xx are for the parity bits
   .INITP_00(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INITP_01(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INITP_02(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INITP_03(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INITP_04(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INITP_05(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INITP_06(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INITP_07(256'h0000000000000000000000000000000000000000000000000000000000000000),

   // The next set of INITP_xx are valid when configured as 36Kb
   .INITP_08(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INITP_09(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INITP_0A(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INITP_0B(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INITP_0C(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INITP_0D(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INITP_0E(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INITP_0F(256'h0000000000000000000000000000000000000000000000000000000000000000)
) BRAM_TDP_MACRO_inst (
   .DOA(DOA),       // Output port-A data, width defined by READ_WIDTH_A parameter
   .DOB(DOB),       // Output port-B data, width defined by READ_WIDTH_B parameter
   .ADDRA(ADDRA),   // Input port-A address, width defined by Port A depth
   .ADDRB(ADDRB),   // Input port-B address, width defined by Port B depth
   .CLKA(CLKA),     // 1-bit input port-A clock
   .CLKB(CLKB),     // 1-bit input port-B clock
   .DIA(DIA),       // Input port-A data, width defined by WRITE_WIDTH_A parameter
   .DIB(DIB),       // Input port-B data, width defined by WRITE_WIDTH_B parameter
   .ENA(ENA),       // 1-bit input port-A enable
   .ENB(ENB),       // 1-bit input port-B enable
   .REGCEA(REGCEA), // 1-bit input port-A output register enable
   .REGCEB(REGCEB), // 1-bit input port-B output register enable
   .RSTA(RSTA),     // 1-bit input port-A reset
   .RSTB(RSTB),     // 1-bit input port-B reset
   .WEA(WEA),       // Input port-A write enable, width defined by Port A depth
   .WEB(WEB)        // Input port-B write enable, width defined by Port B depth
);

// End of BRAM_TDP_MACRO_inst instantiation