MACC_MACRO - 2021.2 English

Vivado Design Suite 7 Series FPGA and Zynq-7000 SoC Libraries Guide (UG953)

Document ID
UG953
Release Date
2021-10-22
Version
2021.2 English

Macro: Multiplier/Accumulator

Introduction

MACC_MACRO simplifies the instantiation of the DSP48 block when used in simple signed multiplier/accumulator mode. It features parameterizable input and output widths and latencies that ease the integration of the DSP48 block into HDL.

Port Descriptions

Port Direction Width Function
P Output Variable width, equals the value of the WIDTH_A attribute plus the value of the WIDTH_B attribute. Primary data output.
A Input Variable, see WIDTH_A attribute. Multiplier data input.
B Input Variable, see WIDTH_B attribute. Multiplier data input.
CARRYIN Input 1 Carry input.
CE Input 1 Clock enable.
CLK Input 1 Clock.
LOAD Input 1 Load.
LOAD_DATA Input Variable width, equals the value of the WIDTH_A attribute plus the value of the WIDTH_B attribute. In a DSP slice, when LOAD is asserted, loads P with A*B+LOAD_DATA.
RST Input 1 Synchronous Reset.
ADDSUB Input 1 High sets accumulator in addition mode; low sets accumulator in subtraction mode.

Design Entry Method

This unimacro is a parameterizable version of the primitive, and can be instantiated only.
Instantiation Yes
Inference No
IP Catalog No
Macro support Recommended

Available Attributes

Attribute Type Allowed Values Default Description
DEVICE STRING "7SERIES" "7SERIES" Target hardware architecture.
WIDTH_P INTEGER 1 to 48 48 Accumulator output bus width.
WIDTH_A INTEGER 1 to 25 25 Multiplier A-input bus width.
WIDTH_B INTEGER 1 to 18 18 Multiplier B-input bus width.
LATENCY INTEGER 1, 2, 3, 4 3 Number of pipeline registers.
  • 1: MREG == 1
  • 2: AREG == BREG == 1 and MREG == 1 or MREG == 1 and PREG == 1
  • 3: AREG == BREG == 1 and MREG == 1 and PREG == 1
  • 4: AREG == BREG == 2 and MREG == 1 and PREG == 1

VHDL Instantiation Template

Unless they already exist, copy the following four statements and paste them before the entity declaration.
Library UNISIM;
use UNISIM.vcomponents.all;
library UNIMACRO;
use unimacro.Vcomponents.all;

-- MACC_MACRO: Multiple Accumulate Function implemented in a DSP48E
--             7 Series
-- Xilinx HDL Language Template, version 2021.2

MACC_MACRO_inst : MACC_MACRO
generic map (
   DEVICE => "7SERIES",  -- Target Device: "VIRTEX5", "7SERIES", "SPARTAN6"
   LATENCY => 3,         -- Desired clock cycle latency, 1-4
   WIDTH_A => 25,        -- Multiplier A-input bus width, 1-25
   WIDTH_B => 18,        -- Multiplier B-input bus width, 1-18
   WIDTH_P => 48)        -- Accumulator output bus width, 1-48
port map (
   P => P,     -- MACC ouput bus, width determined by WIDTH_P generic
   A => A,     -- MACC input A bus, width determined by WIDTH_A generic
   ADDSUB => ADDSUB, -- 1-bit add/sub input, high selects add, low selects subtract
   B => B,           -- MACC input B bus, width determined by WIDTH_B generic
   CARRYIN => CARRYIN, -- 1-bit carry-in input to accumulator
   CE => CE,      -- 1-bit active high input clock enable
   CLK => CLK,    -- 1-bit positive edge clock input
   LOAD => LOAD, -- 1-bit active high input load accumulator enable
   LOAD_DATA => LOAD_DATA, -- Load accumulator input data,
                           -- width determined by WIDTH_P generic
   RST => RST    -- 1-bit input active high reset
);

-- End of MACC_MACRO_inst instantiation

Verilog Instantiation Template


// MACC_MACRO: Multiply Accumulate Function implemented in a DSP48E
//             7 Series
// Xilinx HDL Language Template, version 2021.2

MACC_MACRO #(
   .DEVICE("7SERIES"), // Target Device: "7SERIES"
   .LATENCY(3),        // Desired clock cycle latency, 1-4
   .WIDTH_A(25),       // Multiplier A-input bus width, 1-25
   .WIDTH_B(18),       // Multiplier B-input bus width, 1-18
   .WIDTH_P(48)        // Accumulator output bus width, 1-48
) MACC_MACRO_inst (
   .P(P),     // MACC output bus, width determined by WIDTH_P parameter
   .A(A),     // MACC input A bus, width determined by WIDTH_A parameter
   .ADDSUB(ADDSUB), // 1-bit add/sub input, high selects add, low selects subtract
   .B(B),     // MACC input B bus, width determined by WIDTH_B parameter
   .CARRYIN(CARRYIN), // 1-bit carry-in input to accumulator
   .CE(CE),     // 1-bit active high input clock enable
   .CLK(CLK),   // 1-bit positive edge clock input
   .LOAD(LOAD), // 1-bit active high input load accumulator enable
   .LOAD_DATA(LOAD_DATA), // Load accumulator input data, width determined by WIDTH_P parameter
   .RST(RST)    // 1-bit input active high reset
);

// End of MACC_MACRO_inst instantiation