Physical Synthesis Phase - 2022.1 English

Vivado Design Suite User Guide: Implementation (UG904)

Document ID
Release Date
2022.1 English

During physical synthesis, the placer can perform various physical optimizations that will optimize the netlist for later placement phases based on the initial placement of the design after the floorplanning stage. For example, for fanout based replication the replicated driver can be co-located with its loads because the initial placement is known. This alleviates congestion that can be introduced when replication is done without knowledge of placement prior to place_design. Optimizations are considered based on internal parameters and for timing based optimizations the timing is evaluated and the optimization is committed if timing is improved. The following optimizations are available as shown in as shown in the following figure.

Figure 1. Summary of Physical Synthesis Optimizations
LUT Decomposition and Combining
LUT Decomposition breaks LUT shapes if it improves timing (only LUTs with SOFT_HLUTNM property are considered). LUT combining combines LUTs if it improves utilization.
Property-Based Retiming
Property-based retiming provides user-controlled retiming through setting a property on a register or LUT. This optimization is ideal for critical paths with sufficient margin on timing startpoints or endpoints. Two properties control retiming in PSIP. PSIP_RETIMING_BACKWARD with value of TRUE performs backward retiming and PSIP_RETIMING_FORWARD with value of TRUE performs forward retiming. The properties can be applied to a register or LUT. When PSIP_RETIMING_FORWARD with value TRUE is applied to a register, PSIP forward retimes over all LUT loads driven by the Q pin of the register. When PSIP_RETIMING_FORWARD with value TRUE is applied to a LUT primitive, the register driving the LUT will be moved to the output of the LUT. When PSIP_RETIMING_BACKWARD with value TRUE is applied to a register, PSIP backward retimes over the LUT driving the D pin of the register. Note that the backward retiming property on the register will not trigger backward retiming over control set pin driver LUTs. When PSIP_RETIMING_BACKWARD with value TRUE is applied to a LUT primitive, the register driven by the LUT will be moved to LUT inputs. Multi-level retiming is supported by applying the property to all LUT primitives along the path. All retimed cells will have the PHYS_OPT_MODIFIED property set to RETIMING.

Retiming does not work for the following:

  • Moving logic across macro, such as BRAM, UltraRAM, and DSPs
  • Register packed in I/O sites
  • Paths with different startpoint/endpoint clocks
  • Paths with timing exceptions
  • Properties that prevent optimization, such as DONT_TOUCH, ASYNC_REG, and so forth.
Very High-Fanout Optimization
Very High-Fanout Optimization replicates registers driving high-fanout nets (fanout > 1000, slack < 2.0 ns).
Critical Cell Optimization
Critical-Cell Optimization replicates cells in failing paths. If the loads on a specific cell are placed far apart, the cell might be replicated with new drivers placed closer to load clusters. This optimizations often applies to nets driving large block RAM or URAM arrays or large number of DSPs as the sites for these blocks are spread over a wider area of the device. High fanout is not a requirement for this optimization to occur (slack < 0.5 ns).
Fanout Optimization
Nets with a MAX_FANOUT property value that is less than the actual fanout of the net are considered for fanout optimization. The user can force the replication of a register or a LUT driving a net by adding the FORCE_MAX_FANOUT property to the net. The value of the FORCE_MAX_FANOUT specifies the maximum physical fanout the nets should have after the replication optimization. The physical fanout in this case refers to the actual site pin loads, not the logical loads. For example if the replica drives multiple LUTRAM loads that are all grouped in the same slice, the combined fanout will be 1 for all of the LUTRAMs in the same slice. The FORCE_MAX_FANOUT forces the replication during physical synthesis regardless of the slack of the signal. The user can force replication based on physical device attributes with the MAX_FANOUT_MODE property. The property can take on the value of CLOCK_REGION, SLR, or MACRO. For example, the MAX_FANOUT_MODE property with a value of CLOCK_REGION replicates the driver based on the physical clock region, the loads placed into same clock region will be clustered together. The MAX_FANOUT_MODE property takes precedence over the FORCE_MAX_FANOUT property and physical synthesis will try to honor both by applying MAX_FANOUT_MODE based optimization first and then all its replicated drivers will inherit the FORCE_MAX_FANOUT property to do further replication within a clock region. This is illustrated in the following figure example where a register drives four loads; two registers and two MACRO loads (Block RAM, UltraRAM or DSP). Replication provides separate drivers for the register loads and MACRO loads and then the driver for the MACRO loads is replicated until the FORCE_MAX_FANOUT property value is satisfied.
Figure 2. Applying MAX_FANOUT_MODE with value MACRO together with FORCE_MAX_FANOUT
DSP Register Optimization
DSP Register Optimization can move registers out of the DSP cell into the logic array or from logic to DSP cells if it improves the delay on the critical path.
Shift Register to Pipeline Optimization
Shift Register to Pipeline Optimization turns a shift register with fixed length to dynamically adjusted register pipeline and places the pipeline optimally to improve timing. Only SRLs with the PHYS_SRL2PIPELINE attribute set to TRUE are considered for this optimization. The pull/push of FFs happens on the SRL's Q-pin. The SRL length needs to be fixed and dynamic SRLs are not supported for this optimization.
Shift Register Optimization
The shift register optimization improves timing on negative slack paths between shift register cells (SRLs) and other logic cells.
Block RAM Register Optimization
Block RAM Register Optimization can move registers out of the block RAM cell into the logic array or from logic to block RAM cells if it improves the delay on the critical path.
URAM Register Optimization
UltraRAM Register Optimization can move registers out of the UltraRAM cell into the logic array or from logic to UltraRAM cells if it improves the delay on the critical path.
Dynamic/Static Region Interface Net Replication
Optimization to replicate drivers on static design to reconfigurable module boundary paths in DFX flow.
Equivalent Driver Rewire Optimization
This optimization redistributes loads between logically-equivalent drivers to minimize routing overlap and provide a more optimal co-location of drivers and loads. This helps reduce utilization and congestion and allows later placer stages to move drivers and loads more optimally to improve QoR.

For more information on these optimizations see Available Physical Optimizations in the Physical Optimization section. Physical synthesis in the placer is run by default in all of the placer directives. At the end of the physical synthesis phase, a table shows the summary of optimizations.