This section dives into software pipelining of loops. This is an important concept that enables the AI Engine to concurrently execute different parts of a program. For example, a loop that requires a total of nine cycles to execute through one iteration is shown in the following figure, where sequential execution all the way to a full overlap pipelining is illustrated.
Counting the cycles through each of these examples, it is clear that the sequential execution requires 27 cycles to fully execute the three loop iterations, while the partially overlapped pipeline requires 13 cycles, and the fully pipelined loop requires only 11 cycles. From a performance perspective, it is therefore desirable to have a fully overlapping pipeline. However, this is not always possible, because resource constraints, as well as inter-iteration loop dependencies can prevent a full overlap (see the following figure).
In this example, the program performs load A (2 x 256-bit) in cycle 2, load B (2 x 256-bit) in cycle 3, and in cycle 6 and 7 it is executes operations on loop variable A. The remaining instructions of this iteration are of no importance with respect to the loop performance analysis.
Cycles 2 and 3 of this loop iteration execute 4 x 256-bit load operations. The required four loads are executed in two cycles because the AI Engines can only execute two loads per cycle. This is called a resource constraint. If the loop containing this iteration is supposed to be pipelined, this constraint limits the overlap to no less than two cycles. Similarly, code dependencies between iterations shown in cycle 6 and 7 can prevent additional overlap. In this case, the next iteration of the loop requires the value of A to be updated before it can be used by the loop, thus, limiting the overlap.
The AI Engine compiler reports on each loop in the following form.
-voption is needed to generate the verbose report.
HW do-loop #397 in "testbench.cc", line 132: (loop #16) : Critical cycle of length 2 : b67 -> b68 -> b67 Minimum length due to resources: 2 Scheduling HW do-loop #397 (algo 1a) -> # cycles: 9 (modulo) -> # cycles: 2 ok (required budget ratio: 1) (resume algo) -> after folding: 2 (folded over 4 iterations) -> HW do-loop #397 in "testbench.cc", line 132: (loop #16) : 2 cycles NOTICE: loop #397 contains folded negative edges NOTICE: postamble created Removing chess_separator blocks (all)
In the AI Engine compiler report
shown previously, the section
Critical cycle of
length provides feedback on code dependencies, while the
Minimum length due to resources indicates minimum
overlap requirement due to resource constraints. The
1a line states the total amount of cycles for a single iteration. Given
these numbers, there are a maximum of five iterations active at a time creating the
The AI Engine compiler reports these five
overlapping iterations (the current iteration plus four folded iterations) in the
resume algo line. In addition, it states the
initiation interval (II), the number of cycles a single iteration has to execute
before the following iteration is started, which is two in this example.
In general, it is sufficient to provide the directive
chess_prepare_for_pipelining to instruct the compiler
to attempt software pipelining. When the number of loop iterations is a compile time
constant, the chess compiler creates the optimum software pipeline.
In the case of a dynamic loop range (defined by a variable
start/end), the compiler requires additional information to create an effective
pipeline loop structure. This is performed through the directive
Details about the
<maximum>) directive can be found in Loops.
(algo 1a) -> # cycles: 167 (exceeds -k 64) -> no folding: 167 -> HW do-loop #511 in "xxxx", line 794: (loop #8): 167 cycles
-voption for the AI Engine compiler in the command line.
Module scheduling report can be generated for module scheduled loops by
specifying the option
-Xchess=main:backend.mist2.xargs=-ggraph for the AI Engine compiler. Module scheduling report will be
available for software pipelined loop with the name *_modulo.rpt in
where * is the block name. The module scheduling report also contains the
information about register live ranges for register files, which may be useful to
find inefficiencies in register assignment and can be improved by using
After compilation and linking is complete, Vitis Analyzer can be used to open the compile log for an individual kernel. For more information about the Vitis Analyzer, see the AI Engine Tools and Flows User Guide (UG1076).