nwl-pcie fd0e0000.pcie: Link is UP PCI host bridge /amba/pcie@fd0e0000 ranges: No bus range found for /amba/pcie@fd0e0000, using [bus 00-ff] MEM 0xe1000000..0xefffffff -> 0xe1000000 nwl-pcie fd0e0000.pcie: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [bus 00-ff] pci_bus 0000:00: root bus resource [mem 0xe1000000-0xefffffff] pci 0000:00:00.0: BAR 8: assigned [mem 0xe1000000-0xe10fffff] pci 0000:01:00.0: BAR 0: assigned [mem 0xe1000000-0xe100ffff 64bit] pci 0000:01:00.0: BAR 6: assigned [mem 0xe1010000-0xe101ffff pref] pci 0000:00:00.0: PCI bridge to [bus 01-0c] pci 0000:00:00.0: bridge window [mem 0xe1000000-0xe10fffff] xilinx-dpdma fd4c0000.dma: Xilinx DPDMA engine is probed xenfs: not registering filesystem on non-xen platform Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled ff000000.serial: ttyPS0 at MMIO 0xff000000 (irq = 217, base_baud = 6250000) is a xuartps console [ttyPS0] enabled console [ttyPS0] enabled bootconsole [uart0] disabled bootconsole [uart0] disabled ff010000.serial: ttyPS1 at MMIO 0xff010000 (irq = 218, base_baud = 6250000) is a xuartps Unable to detect cache hierarchy from DT for CPU 0 brd: module loaded loop: module loaded ahci-ceva fd0c0000.ahci: AHCI 0001.0301 32 slots 2 ports 6 Gbps 0x3 impl platform mode ahci-ceva fd0c0000.ahci: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst scsi host0: ahci-ceva scsi host1: ahci-ceva ata1: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x100 irq 214 ata2: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x180 irq 214 mtdoops: mtd device (mtddev=name/number) must be supplied m25p80 spi0.0: found n25q512a, expected m25p80 m25p80 spi0.0: Controller not in SPI_TX_QUAD mode, just use extended SPI mode m25p80 spi0.0: n25q512a (131072 Kbytes) 8 ofpart partitions found on MTD device spi0.0 Creating 8 MTD partitions on "spi0.0": 0x000000000000-0x000000800000 : "boot" 0x000000800000-0x000000840000 : "bootenv" 0x000000840000-0x000001240000 : "kernel" 0x000001240000-0x000008000000 : "spare" 0x000000000000-0x000000100000 : "qspi-fsbl-uboot" 0x000000100000-0x000000600000 : "qspi-linux" 0x000000600000-0x000000620000 : "qspi-device-tree" 0x000000620000-0x000000c00000 : "qspi-rootfs" libphy: Fixed MDIO Bus: probed CAN device driver interface libphy: MACB_mii_bus: probed macb ff0e0000.ethernet eth0: Cadence GEM rev 0x50070106 at 0xff0e0000 irq 29 (00:0a:35:00:22:01) macb ff0e0000.ethernet eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=ff0e0000.etherne:0c, irq=-1) tg3.c:v3.137 (May 11, 2014) pci 0000:00:00.0: enabling device (0000 -> 0002)