Absolute Maximum Ratings

Table 1. Absolute Maximum Ratings—Power, Voltages, and Current
Symbol	Description¹		Min	Max	Units
V_CCAUX	Programmable logic auxiliary power supply		–0.500	1.650	V
V_{CCAUX_PMC}	Platform management controller (PMC) auxiliary power supply voltage		–0.500	1.650	V
V_{CCAUX_SMON} ²	PMC system monitor power supply relative to GND_SMON		–0.500	1.650	V
V_{CC_BATT}	Battery power supply		–0.500	1.650	V
V_{CC_FUSE}	eFUSE programming power supply		–0.500	2.000	V
V_CCINT	Programmable logic primary power supply		–0.500	0.970	V
V_{CC_CPM5}	CPM5 primary power supply		–0.500	0.970	V
V_{CC_IO} ³	XPIO power supply		–0.500	0.970	V
V_CCO ⁴	XPIO bank 7## and bank 8## output driver power supply Where the bank number is the three-digit bank number beginning with 7 or 8		–0.500	1.650	V
	HDIO bank 3## and bank 4## output driver power supply Where the bank number is the three-digit bank number beginning with 3 or 4		–0.500	3.63	V
	PSIO bank 5## power supplies Where the bank number is the three-digit bank number beginning with 5		–0.500	3.63	V
V_{CC_PMC}	PMC primary power supply		–0.500	0.970	V
V_{CC_PSFP}	PS full-power domain power supply		–0.500	0.970	V
V_{CC_PSLP}	PS low-power domain power supply		–0.500	0.970	V
V_{CC_RAM}	PL RAM and clocking network power supply		–0.500	0.970	V
V_{CC_SOC} ³	Network on Chip (NoC) and DDR memory controller power supply		–0.500	0.970	V
V_IN ^{4, 5}	I/O input voltage for PSIO, HDIO, and XPIO banks		–0.550	V_CCO + 0.550	V
V_REF	PMC system monitor reference input (V_REFP/V_REFN) relative to GND_SMON		–0.500	1.120	V
GTY and GTYP (or GTM) Transceivers
V_{GTY_AVCC} V_{GTM_AVCC}	GTY and GTYP (or GTM) transceiver primary analog power supply⁶		–0.500	0.97	V
V_{GTY_AVCCAUX} V_{GTM_AVCCAUX}	GTY and GTYP (or GTM) transceiver auxiliary analog (PLL) power supply⁶		–0.500	1.650	V
V_{GTY_AVTT} V_{GTM_AVTT}	GTY and GTYP (or GTM) transceiver termination power supply⁶		–0.500	1.320	V
V_{GTY_AVTTRCAL} V_{GTM_AVTTRCAL}	GTY and GTYP (or GTM) transceiver analog resistor calibration power supply⁶		–0.500	1.320	V
V_{CCINT_GT}	Digital supply voltage for select modules in the GTM transceivers		–0.500	0.97	V
V_{GTY_REFCLK_DC} V_{GTM_REFCLK_DC}	Transceiver reference clock absolute input DC voltage		–0.500	1.000	V
V_{GTY_REFCLK_AC} V_{GTM_REFCLK_AC}	Transceiver reference clock absolute input AC voltage⁷		–0.500	1.200	V
V_{IN_DC}	Receiver (RXP/RXN) and transmitter (TXP/TXN) absolute DC voltage	Unpowered	–0.800	0.800	V
V_{IN_DC}		Powered	–0.300	1.000	V
V_{IN_AC+DC}	Receiver (RXP/RXN) and transmitter (TXP/TXN) absolute AC plus DC voltage	Unpowered	–0.800	0.800	V
V_{IN_AC+DC}		Powered	–0.500	1.250	V
I_{DCIN_FLOAT}	DC input current for receiver input pins DC coupled RX termination = floating⁸		–	10	mA
I_{DCIN_GTY_AVTT}	DC input current for GTY and GTYP receiver input pins DC coupled RX termination = V_{GTY_AVTT}		–	16	mA
I_{DCIN_GTM_AVTT}	DC input current for GTM receiver input pins DC coupled RX termination = V_{GTM_AVTT}		–	12	mA
I_{DCIN_GTY_GND}	DC input current for GTY and GTYP receiver input pins DC coupled RX termination = GND		–	16	mA
I_{DCIN_GTM_GND}	DC input current for GTM receiver input pins DC coupled RX termination = GND		–	12	mA
I_{DCIN_PROG}	DC input current for receiver input pins DC coupled RX termination = programmable⁹		–	0	mA
I_{DCOUT_FLOAT}	DC output current for transmitter pins DC coupled RX termination = floating		–	6	mA
I_{DCOUT_GTY_AVTT}	DC output current for transmitter pins DC coupled RX termination = V_{GTY_AVTT}		–	6	mA
Other Ratings
I_DC	Available output current at the pad		–20	20	mA
I_RMS	Available RMS output current at the pad		–20	20	mA
Stresses beyond those listed under Absolute Maximum Ratings might cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those listed under Operating Conditions is not implied. Exposure to Absolute Maximum Ratings conditions for extended periods of time might affect device reliability. V_{CCAUX_SMON} must be connected to V_{CCAUX_PMC} . See Versal ACAP System Monitor Architecture Manual (AM006) for V_{CCAUX_SMON} information and filter considerations. V_{CC_IO} must be connected to V_{CC_SOC}. When operating outside of the recommended operating conditions, refer to Table 1 and Table 2 for maximum overshoot and undershoot specifications. The lower absolute voltage specification always applies. For more information on supported GTY and GTYP (or GTM) transceiver terminations see the Versal ACAP GTY and GTYP Transceivers Architecture Manual (AM002) or Versal ACAP GTM Transceivers Architecture Manual (AM017) . GTY_REFCLK AC signal operates in the reference clock frequency range. See GTY and GTYP Transceiver Reference Clock Switching Characteristics. AC coupled operation is not supported for RX termination = floating. DC coupled operation is not supported for RX termination = programmable.

Table 2. Absolute Maximum Ratings—Temperature
Symbol	Description¹	Min	Max	Units
T_STG	Storage temperature (ambient, unpowered)	–55	125	°C
T_SOL ²	Maximum dry rework soldering temperature	–	260	°C
T_j	Maximum junction temperature	–	125	°C
Stresses beyond those listed under Absolute Maximum Ratings might cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those listed under Operating Conditions is not implied. Exposure to Absolute Maximum Ratings conditions for extended periods of time might affect device reliability. For soldering guidelines and thermal considerations, see the Versal ACAP Packaging and Pinouts Architecture Manual (AM013).