XPLL Switching Characteristics

Versal Premium Series Data Sheet: DC and AC Switching Characteristics (DS959)

Document ID
DS959
Release Date
2024-02-29
Revision
1.5 English
Table 1. XPLL Specification
Symbol Description Performance as a Function of Speed Grade and Operating Voltage (VCC_IO) Units
0.88V (H) 0.80V (M) 0.80V (L) 1
-3 -2 -2 -1 -2 -1
FINMAX_XPLL Maximum input clock frequency 2 1150 1150 1070 984 800 680 MHz
FINMIN_XPLL Minimum input clock frequency 100 100 100 100 100 100 MHz
FINJITTER_XPLL Maximum input clock jitter 3 < 20% of clock input period or 1 ns Max
FINDUTY_XPLL Allowable input duty cycle: 100–399 MHz 35–65 %
Allowable input duty cycle: 400–499 MHz 40–60 %
Allowable input duty cycle: >500 MHz 45–55 %
FPSCLKMAX_XPLL Maximum dynamic phase shift clock frequency 300 300 300 300 300 300 MHz
FPSCLKMIN_XPLL Minimum dynamic phase shift clock frequency 0.01 0.01 0.01 0.01 0.01 0.01 MHz
FVCOMAX_XPLL Maximum XPLL VCO frequency 4320 4320 4320 4320 4320 4320 MHz
FVCOMIN_XPLL Minimum XPLL VCO frequency 2160 2160 2160 2160 2160 2160 MHz
FBANDWIDTH_XPLL XPLL bandwidth at typical 4 14.00 14.00 14.00 14.00 14.00 14.00 MHz
TSTATPHAOFFSET_XPLL Static phase offset of the XPLL outputs 5 0.12 0.12 0.12 0.12 0.12 0.12 ns
TOUTJITTER_XPLL XPLL output jitter Note 6
TOUTDUTY_XPLL XPLL CLKOUT0, CLKOUT1, CLKOUT2, CLKOUT3 duty-cycle precision 7 0.125 0.15 0.15 0.15 0.15 0.15 ns
TLOCKMAX_XPLL XPLL maximum lock time (in non-deskew mode) 100 100 100 100 100 100 µs
TLOCKDESKEWMAX_XPLL XPLL maximum lock time in deskew mode Note 8
FOUTMAX_XPLL XPLL maximum output frequency at CLKOUT0, CLKOUT1, CLKOUT2, CLKOUT3 2,9 1150 1150 1070 984 800 680 MHz
XPLL maximum output frequency at CLKOUTPHY 4266 4266 3933 3733 3933 3733 MHz
FOUTMIN_XPLL XPLL minimum output frequency at CLKOUT0, CLKOUT1, CLKOUT2, CLKOUT3 16.875 16.875 16.875 16.875 16.875 16.875 MHz
XPLL minimum output frequency at CLKOUTPHY 200 200 200 200 200 200 MHz
TPWRDWNMINPULSE_XPLL Minimum power-down pulse width 5.00 5.00 5.00 5.00 5.00 5.00 ns
FPFDMAX_XPLL Maximum frequency at the phase frequency detector with bandwidth set to High optimized 667.5 667.5 667.5 667.5 667.5 667.5 MHz
FPFDMIN_XPLL Minimum frequency at the phase frequency detector 100 100 100 100 100 100 MHz
TDESKEWTAPEDELAY_XPLL Nominal tap-delay of the programmable delay in the PD based deskew scheme Note 10
  1. The XPLL is powered by the VCC_IO supply that operates at 0.80V in low (L) voltage operation, see Table 1.
  2. The maximum input clock frequency and output clock frequency at CLKOUT0, CLKOUT1, CLKOUT2, and CLKOUT3 are limited by the global clock buffers. See Table 1.
  3. CLKIN jitter also applies to CLKIN_DESKEW and CLKFB_DESKEW in digital compensation. CLKFBIN applies only to analog compensation. This parameter is in regards to the functionality of the XPLL. Input jitter above ~1 MHz is reduced by the filtering properties of the XPLL. The magnitude of the reduction is found in the Vivado timing report.
  4. The XPLL does not filter typical spread-spectrum input clocks because they are usually far below the loop filter frequencies.
  5. The static offset is measured between any XPLL outputs with identical phase.
  6. Values for this parameter are available in the Vivado timing summary as part of the clock uncertainty equation.
  7. Includes global clock buffer.
  8. The maximum lock time in deskew mode is given by the following formula: Lock time in deskew mode in μs = (208 x (VCO_frequency in MHz) / (CLKIN_DESKEW_frequency in MHz)2 + 100.
  9. XPLL CLKOUTs FMAX is increased in the -1L/-2L speed grade when it directly drives the memory controller at a 1/4 x DDR bit rate. Refer to the DDR bit rate in Table 1.
  10. The value for this parameter is included in compensation delay calculations.