AN Interface Control/Status/Statistics Signals - 2.7 English

1G/10G/25G Switching Ethernet Subsystem Product Guide (PG292)

Document ID
PG292
Release Date
2022-05-11
Version
2.7 English

The following ports are available when the Include AN Logic option is selected in the Configuration tab.

Table 1. AN Interface Control/Status/Statistics Signals
Name Size I/O Description
an_reset_* 1 I Asynchronous active-High reset corresponding to an_clk domain.
an_loc_np_data_* 48 I Local Next Page codeword. This is the 48 bit codeword used if the 'loc_np' input is set. In this data field, the bits NP, ACK, & T, bit positions 15, 14, 12, & 11, are not transferred as part of the next page codeword. These bits are generated in the AN IP. However, the Message Protocol bit, MP, in bit position 13, is transferred.
an_lp_np_data_* 48 O Link Partner Next Page Data. This 48 bit word is driven by the AN IP with the 48 bit next page codeword from the remote link partner.
ctl_autoneg_enable_* 1 I Enable signal for auto-negotiation.
Note: This port is available when Include AXI4-Lite is not selected in the Configuration tab.
ctl_autoneg_bypass_* 1 I Input to disable auto-negotiation and bypass the auto-negotiation function. If this input is asserted, then auto-negotiation is turned off, but the PCS is connected to the output to allow operation.
Note: This port is available when Include AXI4-Lite is not selected in the Configuration tab.
ctl_an_nonce_seed_* 8 I 8-bit seed to initialize the nonce field polynomial generator.
Note: This port is available when Include AXI4-Lite is not selected in the Configuration tab.
ctl_an_pseudo_sel_* 1 I Selects the polynomial generator for the bit 49 random bit generator. If this input is 1, then the polynomial is x7+x6+1. If this input is zero, then the polynomial is x7+x3+1.
Note: This port is available when Include AXI4-Lite is not selected in the Configuration tab.
ctl_restart_negotiation_* 1 I This input is used to trigger a restart of the auto-negotiation, regardless of what state the circuit is currently in.
Note: This port is available when Include AXI4-Lite is not selected in the Configuration tab.
ctl_an_local_fault_* 1 I This input signal is used to set the remote_fault bit of the transmit link codeword.
Note: This port is available when Include AXI4-Lite is not selected in the Configuration tab.
ctl_an_pause_* 1 I This input signal is used to set the PAUSE bit, (C0), of the transmit link codeword. This signal might not be present if the core does not support pause.
Note: This port is available when Include AXI4-Lite is not selected in the Configuration tab.
ctl_an_asmdir_* 1 I This input signal is used to set the ASMDIR bit, (C1), of the transmit link codeword. This signal might not be present if the core does not support pause.
Note: This port is available when Include AXI4-Lite is not selected in the Configuration tab.
ctl_an_fec_10g_request_* 1 I This signal is used to signal the link partner that the local station is requesting clause 74 FEC on the 10Gb/s lane protocols.
Note: This port is available when Include AXI4-Lite is not selected in the Configuration tab.
ctl_an_fec_25g_rs_request_* 1 I This signal is used to signal the link partner that the local station is requesting rs FEC (clause 91 or 108) on the 25Gb/s lane protocols.
Note: This port is available when Include AXI4-Lite is not selected in the Configuration tab.
ctl_an_fec_25g_baser_request_* 1 I Indicates the baser FEC request.
Note: This port is available when Include AXI4-Lite is not selected in the Configuration tab.
ctl_an_fec_ability_override_* 1 I Used to set the clause 74 FEC ability bit in the transmit link codeword. If this input is set, then the FEC ability bit in the transmit link codeword is cleared. This signal might not be present if the IP core does not support clause 74 FEC.
Note: This port is available when Include AXI4-Lite is not selected in the Configuration tab.
ctl_an_loc_np_* 1 I Local Next Page indicator. If this bit is 1, then the AN IP transfers the next page word at input loc_np_data to the remote link partner. If this bit is 0, then the AN IP does not initiate the next page protocol. If the link partner has next pages to send, and the loc_np bit is clear, then the AN IP transfers null message pages.
ctl_an_lp_np_ack_* 1 I Link Partner Next Page Acknowledge. This is used to signal the AN IP that the next page data from the remote link partner at output pin lp_np_data has been read by the local host. When this signal goes High, the AN IP acknowledges reception of the next page codeword to the remote link partner and initiate transfer of the next codeword. During this time, the AN IP removes the lp_np signal until the new next page information is available.
ctl_an_cl91_fec_request_* 1 I This bit is used to request clause 91 FEC.
Note: This port is available when Include AXI4-Lite is not selected in the Configuration tab.
ctl_an_cl91_fec_ability_* 1 I This bit is used to set clause 91 FEC ability.
Note: This port is available when Include AXI4-Lite is not selected in the Configuration tab.
ctl_an_ability_1000base_kx_* 1 I These inputs identify the Ethernet protocol abilities that are advertised in the transmit link codeword to the link partner. A value of 1 indicates that the interface advertises that it supports the protocol.
ctl_an_ability_10gbase_kx4_* 1 I
ctl_an_ability_10gbase_kr_* 1 I
ctl_an_ability_40gbase_kr4_* 1 I
ctl_an_ability_40gbase_cr4_* 1 I
ctl_an_ability_100gbase_cr10_* 1 I
ctl_an_ability_100gbase_kp4_* 1 I
ctl_an_ability_100gbase_kr4_* 1 I
ctl_an_ability_100gbase_cr4_* 1 I
ctl_an_ability_25gbase_krcr_s_* 1 I
ctl_an_ability_25gbase_krcr_* 1 I
ctl_an_ability_25gbase_kr1_* 1 I
ctl_an_ability_25gbase_cr1_* 1 I
ctl_an_ability_50gbase_kr2_* 1 I
ctl_an_ability_50gbase_cr2_* 1 I
stat_an_link_cntl_1000base_kx_* 2 O Link Control outputs from the auto-negotiation controller for the various Ethernet protocols. Settings are as follows:
  • 00: DISABLE; PCS is disconnected
  • 01: SCAN_FOR_CARRIER; RX is connected to PCS
  • 11: ENABLE; PCS is connected for mission mode operation.
  • 10: not used
stat_an_link_cntl_10gbase_kx4_* 2 O
stat_an_link_cntl_10gbase_kr_* 2 O
stat_an_link_cntl_40gbase_kr4_* 2 O
stat_an_link_cntl_40gbase_cr4_* 2 O
stat_an_link_cntl_100gbase_cr10_* 2 O
stat_an_link_cntl_100gbase_kp4_* 2 O
stat_an_link_cntl_100gbase_kr4_* 2 O
stat_an_link_cntl_100gbase_cr4_* 2 O
stat_an_link_cntl_25gbase_krcr_s_* 2 O
stat_an_link_cntl_25gbase_krcr_* 2 O
stat_an_link_cntl_25gbase_kr1_* 2 O
stat_an_link_cntl_25gbase_cr1_* 2 O
stat_an_link_cntl_50gbase_kr2_* 2 O
stat_an_link_cntl_50gbase_cr2_* 2 O
stat_an_fec_enable_* 1 O Used to enable the use of clause 74 FEC on the link.
stat_an_tx_pause_enable_* 1 O Used to enable station-to-station (global) pause packet generation in the transmit path to control data flow in the receive path.
stat_an_rx_pause_enable_* 1 O Used to enable station-to-station (global) pause packet interpretation in the receive path, in order to control data flow from the transmitter.
stat_an_autoneg_complete_* 1 O Indicates the auto-negotiation is complete and rx link status from the PCS has been received.
stat_an_parallel_detection_fault_* 1 O Indicated a parallel detection fault during auto-negotiation.
stat_an_lp_ability_1000base_kx_* 1 O These signals indicate the advertised protocol from the link partner. They all become valid from the link partner. They all become valid when the output signal stat_an_lp_ability_valid is asserted. A value of 1 indicates that the protocol is advertised as supported by the link partner.
stat_an_lp_ability_10gbase_kx4_* 1 O
stat_an_lp_ability_10gbase_kr_* 1 O
stat_an_lp_ability_40gbase_kr4_* 1 O
stat_an_lp_ability_40gbase_cr4_* 1 O
stat_an_lp_ability_100gbase_cr10_* 1 O
stat_an_lp_ability_100gbase_kp4_* 1 O
stat_an_lp_ability_100gbase_kr4_* 1 O
stat_an_lp_ability_100gbase_cr4_* 1 O
stat_an_lp_ability_25gbase_krcr_s_* 1 O
stat_an_lp_ability_25gbase_krcr_* 1 O
stat_lp_ability_25gbase_cr1_* 1 O Indicates the advertised protocol from the link partner. Becomes valid when the output signal stat_AN_lp_Extended_Ability_Valid is asserted. A value of 1 indicates that the protocol is advertised as supported by the link partner.
stat_an_rxcdrhold_* 1 O Indicates the rx cdr hold signal.
stat_an_lp_pause_* 1 O This signal indicates the advertised value of the PAUSE bit, (C0), in the receive link codeword from the link partner. It becomes valid when the output signal stat_an_lp_ability_valid is asserted.
stat_an_lp_asm_dir_* 1 O This signal indicates the advertised value of the ASMDIR bit, (C1), in the receive link codeword from the link partner. It becomes valid when the output signal stat_an_lp_ability_valid is asserted.
stat_an_lp_rf_* 1 O This bit indicates link partner remote fault.
stat_an_lp_fec_10g_ability_* 1 O This signal indicates the clause 74 FEC ability associated with 10Gb/s lane protocols that is being advertised by the link partner. It becomes valid when the output signal stat_an_lp_ability_valid is asserted.
stat_an_lp_fec_10g_request_* 1 O This signal indicates that the link partner is requesting that the clause 74 FEC be used on the 10Gb/s lane protocols.It becomes valid when the output signal stat_an_lp_ability_valid is asserted.
stat_an_lp_fec_25g_rs_request_* 1 O This signal indicates that the link partner is requesting the clause 91 (or 108) rs FEC be used for the 25gb/s lane protocols. It becomes valid when the output signal stat_an_lp_ability_valid is asserted.
stat_an_lp_fec_25g_baser_request_* 1 O This signal indicates that the link partner is requesting the clause 74 FEC be used for the 25Gb/s lane base-r protocols. It becomes valid when the output signal stat_an_lp_ability_valid is asserted.
stat_an_lp_autoneg_able_* 1 O This output signal indicates that the link partner is able to perform auto-negotiation. It becomes valid when the output signal stat_an_lp_ability_valid is asserted.
stat_an_lp_ability_valid_* 1 O This signal indicates when all of the link partner advertisements become valid.
stat_an_loc_np_ack_* 1 O

This signal is used to indicate to the local host that the local next page data, presented at input pin loc_np_data, has been taken.

This signal pulses High for 1 clock period when the AN IP samples the next page data on input pin loc_np_data. When the local host detects this signal High, it must replace the 48 bit next page codeword at input pin 'loc_np_data' with the next 48 bit codeword to be sent. If the local host has no more next pages to send, then it must clear the loc_np input.

stat_an_lp_np_* 1 O Link Partner Next Page. This signal is used to indicate that there is a valid 48-bit next page codeword from the remote link partner at output pin lp_np_data. This signal is driven Low when the lp_np_ack input signal is driven High, indicating that the local host has read the next page data. It remains Low until the next codeword becomes available on the lp_np_data output pin, then the lp_np output is driven High again.
stat_an_lp_ability_25gbase_kr1_* 1 O Indicates the advertised protocol from the link partner. Becomes valid when the output signal stat_an_lp_extended_ability_valid is asserted. A value of 1 indicates that the protocol is advertised as supported by the link partner.
stat_an_link_cntl_25gbase_cr1_* 1 O Indicates the advertised protocol from the link partner. Becomes valid when the output signal stat_an_lp_extended_ability_valid is asserted. A value of 1 indicates that the protocol is advertised as supported by the link partner.
stat_an_lp_ability_50gbase_kr2_* 1 O Indicates the advertised protocol from the link partner. Becomes valid when the output signal stat_an_lp_extended_ability_valid is asserted. A value of 1 indicates that the protocol is advertised as supported by the link partner.
stat_an_lp_ability_50gbase_cr2_* 1 O Indicates the advertised protocol from the link partner. Becomes valid when the output signal stat_an_lp_extended_ability_valid is asserted. A value of 1 indicates that the protocol is advertised as supported by the link partner.
stat_an_lp_ability_extended_fec_* 4 O This output indicates the extended FEC abilities.
stat_an_rs_fec_enable_* 1 O Used to enable the use of clause 91 FEC on the link.
stat_an_lp_extended_ability_valid_* 1 O When this bit is 1, it indicates that the detected extended abilities are valid.
stat_an_switch_speed_* 1 O

This bit indicates that the AN module requests a speed switch to complete the Auto-Negotiation. Core speed switches between 10G and 1G to perform DME transaction or Parallel detection.