The following table lists the default jumper settings.
Callout | Reference Design | Function | Default | Schematic Page |
---|---|---|---|---|
1 | J1 | POR_OVERRIDE | 2-3 | 3 |
1-2: Enable | ||||
2-3: Disable | ||||
2 | J2 | SYSMON I2C Address | ON | 3 |
OFF: SYSMON_VP_R floating | ||||
ON: SYSMON_VP_P pulled down | ||||
J3 | SYSMON I2C Address | ON | 3 | |
OFF: SYSMON_VN_R floating | ||||
ON: SYSMON_VP_N pulled down | ||||
J4 | SYSMON VREFP | 1-2 | 3 | |
1-2: 1.25V VREFP connected to fpga | ||||
2-3: VREFP connected to GND | ||||
3 | J15 | Reset Sequencer PS_POR_B | ON | 10 |
OFF: Sequencer does not control PS_POR_B | ||||
ON: Sequencer can control PS_POR_B | ||||
J16 | Reset Sequencer PS_SRST_B | ON | 10 | |
OFF: Sequencer does not control PS_SRST_B | ||||
ON: Sequencer can control PS_SRST_B | ||||
J17 | Reset Sequencer inhibit | OFF | 10 | |
OFF: Sequencer normal operation | ||||
ON: Sequencer inhibit (resets will stay asserted) | ||||
4 | ULPI USB3320 U6 ULPIO_VBUS_SEL option jumper | OFF | 20 | |
J19 | ON: Selects U17 MIC2544A switch 5V for VBUS | |||
OFF: Normal operation, VBUS from J18 USB3.0 conn. | ||||
J20 | USB 3.0 Connector J18 Shield connection options | 2-3 | 20 | |
1-2: J20 shield capacitor C171 to GND | ||||
2-3: J20 shield directly to GND | ||||
5 | J22 | SD3.0 U107 IP4856CX25 level-trans. ref. voltage select | 1-2 | 24 |
1-2: Track SD3.0 J12 socket UTIL_3V3 3.3V | ||||
2-3: GND = revert to internal voltage reference | ||||
7 | J39 | zSFP0 J29 LT enable jumper | OFF | 33 |
ON: zSFP0 TX_DISABLE = GND = enabled | ||||
OFF: zSFP0 TX_DISABLE = high = disabled | ||||
J44 | zSFP1 J29 LL enable jumper | OFF | 33 | |
ON: zSFP1 TX_DISABLE = GND = enabled | ||||
OFF: zSFP1 TX_DISABLE = high = disabled | ||||
8 | J32 | zSFP2 J29 RT enable jumper | OFF | 33 |
ON: zSFP2 TX_DISABLE = GND = enabled | ||||
OFF: zSFP2 TX_DISABLE = high = disabled | ||||
J35 | zSFP3 J29 RL enable jumper | OFF | 33 | |
ON: zSFP3 TX_DISABLE = GND = enabled | ||||
OFF: zSFP3 TX_DISABLE = high = disabled | ||||
31 | J148 |
Voltage selection jumper for Zynq UltraScale+ RFSoC |
ON | 53 |
ON: ADC_AVCC=1.01V for ZU67DR device (DFE) |
||||
OFF: ADC_AVCC=0.925V for ZU47DR device (Gen3) |