PMC Quad-SPI Controller Interface

Versal Premium Series Data Sheet: DC and AC Switching Characteristics (DS959)

Document ID
DS959
Release Date
2024-02-29
Revision
1.5 English
Table 1. Quad-SPI Interface
Symbol Description 1, 2 Min Max Units
Quad-SPI device clock frequency operating at >100 MHz up to 150 MHz. Loopback enabled. 3
FQSPI_CLK Quad-SPI device clock frequency 100 150 MHz
FQSPI_REFCLK 4 Quad-SPI reference clock frequency 2 × FQSPI_CLK MHz
TQSPIDCK Setup time, all inputs 0.77 ns
TQSPICKD Hold time, all inputs 1.0 ns
TQSPICKO Clock to output delay, all outputs 2.9 4.5 ns
TQSPICSCLK 5 Chip select asserted to next clock edge 5.0 ns
TQSPICLKCS Clock edge to chip select deasserted 5.0 ns
TDCQSPICLK Quad-SPI clock duty cycle 45 55 %
Quad-SPI device clock frequency operating at >37.5 MHz up to 100 MHz. Loopback enabled. 3
FQSPI_CLK Quad-SPI device clock frequency 37.5 100 MHz
FQSPI_REFCLK 4 Quad-SPI reference clock frequency 2 × FQSPI_CLK MHz
TQSPIDCK Setup time, all inputs 2.0 ns
TQSPICKD Hold time, all inputs 0.0 ns
TQSPICKO Clock to output delay, all outputs 3.2 7.8 ns
TQSPICSCLK 5 Chip select asserted to next clock edge 5.0 ns
TQSPICLKCS Clock edge to chip select deasserted 5.0 ns
TDCQSPICLK Quad-SPI clock duty cycle 45 55 %
Quad-SPI device clock frequency operating at ≤37.5 MHz. Loopback disabled.
FQSPI_CLK Quad-SPI device clock frequency   37.5 MHz
FQSPI_REFCLK 4 Quad-SPI reference clock frequency   300 MHz
TQSPIDCK Setup time, all inputs 19.1 ns
TQSPICKD Hold time, all inputs 0.0 ns
TQSPICKO Clock to output delay, all outputs 5.2 21.5 ns
TQSPICSCLK Chip select asserted to next clock edge 9.0 ns
TQSPICLKCS 5 Clock edge to chip select deasserted 9.0 ns
TDCQSPICLK Quad-SPI clock duty cycle 45 55 %
  1. The test conditions are configured for the generic Quad-SPI interface with a 12 mA drive strength, fast slew rate, and load conditions (15 pF/30 pF for a Quad-SPI device clock frequency up to 100 MHz and 15 pF for a Quad-SPI device clock frequency > 100 MHz), tested at 3.3V and 1.8V.
  2. 30 pF loads are for QSPI dual-stacked or QSPI dual-parallel modes.
  3. When the Quad-SPI device clock frequency is >37.5 MHz, the Quad-SPI loopback clock output (QSPI_LPBK_CLK) must be enabled in the control, interface, and processing system (CIPS), and the associated MIO[6] pin must be left unconnected on the board.
  4. The Quad-SPI reference clock frequency must be 2x the Quad-SPI device clock frequency when it is >37.5 MHz.
  5. TQSPICSCLK is only valid when two reference clock cycles are programmed between the chip select and clock.